Jie,

 

My board is in use at this time so I cannot do this test for you. However I did look at  the Bluetooth beacon sample and I see that it is setting some Bluetooth related CONFIG  settings that are not tested in the BOARD=tileTile make. They are tested  in the arduino_101 make. I suggest you do a make of the Bluetooth beacon sample using BOARD=Arduino_101 and see if that helps.

 

Graham

 

From: Jie Zhou [mailto:zhoujie@...]
Sent: Wednesday, October 11, 2017 6:09 PM

To: Graham Stott <gbcstott1@...>
Cc: zephyr-devel@lists.zephyrproject.org
Subject: Re: [Zephyr-devil] Tiny tile Zephyr implementation

 

Hi Graham,

 

Could you flash the beacon example in zephyr? The path is samples/bluetooth/beacon. You might have to flash the hci_uart example, which is also in the bluetooth sample directory, to update the firmware. If you can do that and open minicom and see the outputs then we might be in luck and will switch over to the curienano.

 

Thank you very much,

Jie 

 

On Wed, Oct 11, 2017 at 2:36 PM, Graham Stott <gbcstott1@...> wrote:

Jie,

 

I do not have the TinyTile board so I cannot try flashing it. However I do have the DFRobot CurieNano which is a similar board. I have no problem flashing this board. I used the instructions (DFU) for Arduino 101.

 

Graham

 

From: Jie Zhou [mailto:zhoujie@...]
Sent: Wednesday, October 11, 2017 3:11 PM
To: Graham Stott <gbcstott1@...>
Cc: zephyr-devel@lists.zephyrproject.org
Subject: Re: [Zephyr-devil] Tiny tile Zephyr implementation

 

Hi Graham,

Thanks for responding! About the similarities of TinyTILE and Arduino101, although the chip is the same, we have been trying to flash applications to tinyTILE for a while now. The arduino can be flash with DFU using the FTDI cable, but tinyTILE doesn't respond to minicom after flashing. We have some inconsistent success with flashing tinyTILE via Flyswatter and settling the port to ttyACM0. Either there is some issues with tinyTILE support from zephyr or the protocol of the chip is different than Arduino.

 

Thanks,

Jie

 

On Tue, Oct 10, 2017 at 12:29 PM, Graham Stott <gbcstott1@...> wrote:

I meant to also say to look at projects for Arduino/Genuine 101 as tiny Tile is a scaled down version of this board.

 

From: zephyr-devel-bounces@lists.zephyrproject.org [mailto:zephyr-devel-bounces@lists.zephyrproject.org] On Behalf Of Graham Stott
Sent: Tuesday, October 10, 2017 2:01 PM
To: 'Jie Zhou' <zhoujie@...>; zephyr-devel@lists.zephyrproject.org
Subject: Re: [Zephyr-devel] Tinytile Zephyr implementation

 

As tinyTile is basically just a version of the Intel® Curie™ module, you can look for projects under Curie. Yes. It has additional pins but the rest is the same

 

Graham

 

From: zephyr-devel-bounces@lists.zephyrproject.org [mailto:zephyr-devel-bounces@lists.zephyrproject.org] On Behalf Of Jie Zhou
Sent: Tuesday, October 10, 2017 1:21 AM
To: zephyr-devel@lists.zephyrproject.org
Subject: [Zephyr-devel] Tinytile Zephyr implementation

 

Hi All,

 

Has anyone done anything with tinyTILE? Since the board is quite new I was wondering if someone has done a project with Zephyr OS on tinyTILE. The specs of the chip looks promising for IoT implementations. Any info or the setup you are using will help. I'm trying to evaluate the capability of tinyTILE with Zephyr.

 

Thanks,

Jie