Date   

Re: ble ipsp sample with global prefix

Daniel Widmann
 

On the Linux side I do:
ping6 aaab::e73f:77ff:fef5:491e

The Zephyr device receives the request, but Zephyr doesn't reply. Zephyr can't find the L2 address of the Linux machine because the Linux machine doesn't reply to the neighbor advertisements.

I added the pcap and a wireshark screenshot.


 


On Wed, Feb 1, 2017 at 1:59 PM, Luiz Augusto von Dentz <luiz.dentz@...> wrote:
Hi Daniel,

On Wed, Feb 1, 2017 at 12:49 AM, Daniel Widmann
<widmann.daniel@...> wrote:
> I am running the bluetooth ipsp sample on a NRF51822, which works after
> tweaking the network buffer sizes. I can ping the link-local fe80 address of
> the zephyr device. To provide the device with a global prefix, I am running
> radvd (on ubuntu 17, on-linkflag is not set), which also works fine.
>
> But when I try to ping the global ip address of the zephyr device, I don't
> get a reply. After looking into the wireshark logs, it turns out the zephyr
> device tries to do a neighbor solicitation for the global ip address of the
> Linux host. But Linux doesn't send a neighbor advertisement.

What command did you use? Perhaps:

ping -I bt0 2001:db8::1
connect: Network is unreachable

It looks like there is no advertisement for this address from zephyr
so the Linux side don't even attempt to send anything.

> Should Zephyr send the packet to the default router instead? I think it
> would make sense as the prefix was announced without the on-link flag.
> Any ideas how to fix this either on the Zephyr or the Linux side?

Well if zephyr would receive anything, but apparently it never leaves
the Linux side.

>
> This is the iface output:
>
> net> iface
> Interface 0x20000bc0
> ====================
> TX stack size 1200/1296 bytes unused 812 usage 388/1200 (26 %)
> Link addr : E5:3F:77:F5:49:1E
> MTU       : 1280
> IPv6 unicast addresses (max 3):
>         2001:db8::1 manual tentative infinite
>         fe80::e73f:77ff:fef5:491e autoconf preferred infinite
>         aaab::e73f:77ff:fef5:491e autoconf preferred
> IPv6 multicast addresses (max 2):
>         ff84::2
> IPv6 prefixes (max 2):
>         <none>
> IPv6 default router :
>         fe80::21a:7dff:feda:7110
> IPv6 hop limit           : 64
> IPv6 base reachable time : 30000
> IPv6 reachable time      : 20
>
>
> Cheers,
> Daniel
>
> _______________________________________________
> Zephyr-devel mailing list
> Zephyr-devel@lists.zephyrproject.org
> https://lists.zephyrproject.org/mailman/listinfo/zephyr-devel
>



--
Luiz Augusto von Dentz


Re: ble ipsp sample with global prefix

Luiz Augusto von Dentz
 

Hi Daniel,

On Wed, Feb 1, 2017 at 12:49 AM, Daniel Widmann
<widmann.daniel@gmail.com> wrote:
I am running the bluetooth ipsp sample on a NRF51822, which works after
tweaking the network buffer sizes. I can ping the link-local fe80 address of
the zephyr device. To provide the device with a global prefix, I am running
radvd (on ubuntu 17, on-linkflag is not set), which also works fine.

But when I try to ping the global ip address of the zephyr device, I don't
get a reply. After looking into the wireshark logs, it turns out the zephyr
device tries to do a neighbor solicitation for the global ip address of the
Linux host. But Linux doesn't send a neighbor advertisement.
What command did you use? Perhaps:

ping -I bt0 2001:db8::1
connect: Network is unreachable

It looks like there is no advertisement for this address from zephyr
so the Linux side don't even attempt to send anything.

Should Zephyr send the packet to the default router instead? I think it
would make sense as the prefix was announced without the on-link flag.
Any ideas how to fix this either on the Zephyr or the Linux side?
Well if zephyr would receive anything, but apparently it never leaves
the Linux side.


This is the iface output:

net> iface
Interface 0x20000bc0
====================
TX stack size 1200/1296 bytes unused 812 usage 388/1200 (26 %)
Link addr : E5:3F:77:F5:49:1E
MTU : 1280
IPv6 unicast addresses (max 3):
2001:db8::1 manual tentative infinite
fe80::e73f:77ff:fef5:491e autoconf preferred infinite
aaab::e73f:77ff:fef5:491e autoconf preferred
IPv6 multicast addresses (max 2):
ff84::2
IPv6 prefixes (max 2):
<none>
IPv6 default router :
fe80::21a:7dff:feda:7110
IPv6 hop limit : 64
IPv6 base reachable time : 30000
IPv6 reachable time : 20


Cheers,
Daniel

_______________________________________________
Zephyr-devel mailing list
Zephyr-devel@lists.zephyrproject.org
https://lists.zephyrproject.org/mailman/listinfo/zephyr-devel


--
Luiz Augusto von Dentz


Trouble configuring arduino101 via zephyr

Anjali Asar <anjaliasar@...>
 

Hi, not sure if this is the right forum for this, but trying my luck. if not, please do direct me towards the right one.

I'm having trouble flashing the arduino101.
i've followed all the instructions available still, tho it says download complete, the code doesnt seem to have been downloaded.

The code i am trying is the sample code provided, "blinky". The LED doesn't light up. i have tried various pins apart from the on board LED too.

 Is there any extra configuration that i have to do to make it work?
Note: i am using a windows 8 pc


Network setting on galileo board

김정훈 <jhun1105.kim@...>
 

Hi all,

 

I am trying to test samples/net/echo_client, samples/net/echo_server on 2 Intel Galileo Gen1 Boards using zephyr-project(commit : f5eeaf95277be5792279499fa9c65d6d4423a0d2).

My testing enviorment is Galileo(Server) - Hub - Galileo(Client).

But there are no any conf file for galileo board. So i used prj_qemu_x86.conf file and modified makefiles for galileo board.

/samples/net/echo_client/Makefile :

/samples/net/echo_server/Makefile :

-BOARD ?= qemu_x86
+BOARD ?= galileo

And then i attached output config files and log files.

 

But there are no response.

I think this is due to the gateway, netmask.

Please share it if anyone have solution.

 

Server's log

WARNING: no console will be available to OS
error: no suitable video mode found.
shell> [echo-server] [INF] init_app: Run echo server
[echo-server] [INF] receive: Starting to wait

shell>
shell>
shell> select net
net> iface
Interface 0x0010f620
====================
TX stack size 1200/1256 bytes unused 960 usage 240/1200 (16 %)
Link addr : 10:00:00:00:00:8A
MTU       : 1500
IPv4 unicast addresses (max 1):
        192.0.2.1 manual preferred infinite
IPv4 multicast addresses (max 1):
        <none>
IPv4 gateway : 0.0.0.0
IPv4 netmask : 0.0.0.0

net> conn
Context         Local                   Remote                  Iface           Flags
0x00110820      0.0.0.0 0.0.0.0 0x0010f620      4DU
0x0011085c      0.0.0.0 0.0.0.0 0x0010f620      4ST

TCP             State           Src port  Dst port  Send-Seq   Send-Ack   MSS
0x00110ac0                    4242         0 849387123         0 1460
net> conn
Context         Local                   Remote                  Iface           Flags
0x00110820      0.0.0.0 0.0.0.0 0x0010f620      4DU
0x0011085c      0.0.0.0 0.0.0.0 0x0010f620      4ST

TCP             State           Src port  Dst port  Send-Seq   Send-Ack   MSS
0x00110ac0                    4242         0 849387123         0 1460
net>

 

Client's log

WARNING: no console will be available to OS
error: no suitable video mode found.
shell> [echo-client] [INF] init_app: Run echo client
[echo-client] [INF] send_udp: Starting to send IPv4 data
[echo-client] [DBG] send_udp: (0x00112660): Waiting IPv4 packet

shell>
shell>
shell>
shell> [echo-client] [ERR] wait_reply: wait_reply returned on time out
[echo-client] [DBG] send_udp: (0x00112660): Waited 490 bytes but did not receive them.
[echo-client] [DBG] send_udp: (0x00112660): Waiting IPv4 packet
select [echo-client] [ERR] wait_reply: wait_reply returned on time out
[echo-client] [DBG] send_udp: (0x00112660): Waited 1200 bytes but did not receive them.
[echo-client] [DBG] send_udp: (0x00112660): Waiting IPv4 packet
net
net> [echo-client] [ERR] wait_reply: wait_reply returned on time out
[echo-client] [DBG] send_udp: (0x00112660): Waited 1074 bytes but did not receive them.
[echo-client] [DBG] send_udp: (0x00112660): Waiting IPv4 packet

net>
net> iface
Interface 0x0010fe80
====================
TX stack size 1200/1256 bytes unused 920 usage 280/1200 (19 %)
Link addr : 10:00:00:00:00:86
MTU       : 1500
IPv4 unicast addresses (max 1):
        192.0.2.2 manual preferred infinite
IPv4 multicast addresses (max 1):
        <none>
IPv4 gateway : 0.0.0.0
IPv4 netmask : 0.0.0.0

net> [echo-client] [ERR] wait_reply: wait_reply returned on time out
[echo-client] [DBG] send_udp: (0x00112660): Waited 880 bytes but did not receive them.
[echo-client] [DBG] send_udp: (0x00112660): Waiting IPv4 packet
conn[echo-client] [ERR] wait_reply: wait_reply returned on time out
[echo-client] [DBG] send_udp: (0x00112660): Waited 826 bytes but did not receive them.
[echo-client] [DBG] send_udp: (0x00112660): Waiting IPv4 packet

Context         Local                   Remote                  Iface           Flags
0x00111000      192.0.2.2       0.0.0.0 0x0010fe80      4DU
0x0011103c      192.0.2.2       192.0.2.1       0x0010fe80      4ST

TCP             State           Src port  Dst port  Send-Seq   Send-Ack   MSS
0x001112a0                    8484      4242 172759034         0 1460
net> [echo-client] [ERR] wait_reply: wait_reply returned on time out
[echo-client] [DBG] send_udp: (0x00112660): Waited 992 bytes but did not receive them.
[echo-client] [DBG] send_udp: (0x00112660): Waiting IPv4 packet
[echo-client] [ERR] wait_reply: wait_reply returned on time out
[echo-client] [DBG] send_udp: (0x00112660): Waited 132 bytes but did not receive them.
[echo-client] [DBG] send_udp: (0x00112660): Waiting IPv4 packet
[echo-client] [ERR] wait_reply: wait_reply returned on time out

 

Regards,
Junghun Kim

 

 


ble ipsp sample with global prefix

Daniel Widmann
 

I am running the bluetooth ipsp sample on a NRF51822, which works after tweaking the network buffer sizes. I can ping the link-local fe80 address of the zephyr device. To provide the device with a global prefix, I am running radvd (on ubuntu 17, on-linkflag is not set), which also works fine. 

But when I try to ping the global ip address of the zephyr device, I don't get a reply. After looking into the wireshark logs, it turns out the zephyr device tries to do a neighbor solicitation for the global ip address of the Linux host. But Linux doesn't send a neighbor advertisement.

Should Zephyr send the packet to the default router instead? I think it would make sense as the prefix was announced without the on-link flag. 
Any ideas how to fix this either on the Zephyr or the Linux side?


This is the iface output:
net> iface
Interface 0x20000bc0
====================
TX stack size 1200/1296 bytes unused 812 usage 388/1200 (26 %)
Link addr : E5:3F:77:F5:49:1E
MTU       : 1280
IPv6 unicast addresses (max 3):
        2001:db8::1 manual tentative infinite
        fe80::e73f:77ff:fef5:491e autoconf preferred infinite
        aaab::e73f:77ff:fef5:491e autoconf preferred
IPv6 multicast addresses (max 2):
        ff84::2
IPv6 prefixes (max 2):
        <none>
IPv6 default router :
        fe80::21a:7dff:feda:7110
IPv6 hop limit           : 64
IPv6 base reachable time : 30000
IPv6 reachable time      : 20

Cheers,
Daniel


Daily Gerrit Digest

donotreply@...
 

NEW within last 24 hours:
- https://gerrit.zephyrproject.org/r/10679 : net: Add ll addresses on net_if_send_data
- https://gerrit.zephyrproject.org/r/10676 : gpio/stm32: fix in setting alternative function
- https://gerrit.zephyrproject.org/r/10678 : net: iface: Fix net_if_get_by_iface return value
- https://gerrit.zephyrproject.org/r/10677 : net: iface: Fix bad comparisons in net_if
- https://gerrit.zephyrproject.org/r/10674 : net: tests: Add unit tests for net_nbuf_compact()
- https://gerrit.zephyrproject.org/r/10673 : net: nbuf: Removing dead code from net_nbuf_compact()
- https://gerrit.zephyrproject.org/r/10672 : gitignore: Ignore Eclipse (Xtensa Xplorer) project files.
- https://gerrit.zephyrproject.org/r/10671 : sanitycheck: support other simulators (xt-run and/or xtsc) than QEMU.
- https://gerrit.zephyrproject.org/r/10670 : Xtensa port: Added arch .ini file to support xt-sim simulations in snitycheck.
- https://gerrit.zephyrproject.org/r/10669 : Xtensa port: Removed duplicate file and renamed to sys_io.h as other platforms.
- https://gerrit.zephyrproject.org/r/10668 : net: context: Assign a random port number when context is created
- https://gerrit.zephyrproject.org/r/10667 : libc/minimal: Fix definition of ssize_t
- https://gerrit.zephyrproject.org/r/10666 : Xtensa port: Changed default core to D_233L.
- https://gerrit.zephyrproject.org/r/10665 : Xtensa port: Fixed RAMABLE_REGION in linker scripts.
- https://gerrit.zephyrproject.org/r/10663 : Bluetooth: RFCOMM: Fix session timer during acl disc
- https://gerrit.zephyrproject.org/r/10660 : Xtensa port: Fixed Swap function not updating _kernel.current.
- https://gerrit.zephyrproject.org/r/10659 : Xtensa port: Removed warnings related to function _NanoFatalErrorHandler.
- https://gerrit.zephyrproject.org/r/10650 : doc: Bluetooth: fix "Initialization" section
- https://gerrit.zephyrproject.org/r/10656 : net/mqtt: Remove redundant line
- https://gerrit.zephyrproject.org/r/10653 : Xtensa port: Added missing initalization of thread base sturct in _new_thread.

UPDATED within last 24 hours:
- https://gerrit.zephyrproject.org/r/10627 : RFC: DTS: Kinetis: Add base support for Kinetis
- https://gerrit.zephyrproject.org/r/9692 : doc: Include main Network APIs doxygen documentation
- https://gerrit.zephyrproject.org/r/10647 : doc: net: Migrate from Zephyr 1.6 to 1.7
- https://gerrit.zephyrproject.org/r/10628 : RFC: DTS: Kinetis: Add FRDM_K64F support
- https://gerrit.zephyrproject.org/r/9460 : Bluetooth: AVDTP: Add AVDTP Discover Function Definition
- https://gerrit.zephyrproject.org/r/9663 : Bluetooth: AVDTP: Add AVDTP Receive Function
- https://gerrit.zephyrproject.org/r/10633 : samples/drivers: STM32F4x flash
- https://gerrit.zephyrproject.org/r/10632 : flash/stm32: driver for STM32F4x series
- https://gerrit.zephyrproject.org/r/10183 : irq: introduce 'direct' interrupt API definition
- https://gerrit.zephyrproject.org/r/10415 : uart: update stm32 uart to support LL clock control driver
- https://gerrit.zephyrproject.org/r/10413 : gpio: update stm32 gpio to support LL clock control driver
- https://gerrit.zephyrproject.org/r/10414 : pinmux: update stm32 pinmux to support LL clock control driver
- https://gerrit.zephyrproject.org/r/10629 : RFC: DTS: Kinetis: Add support for Hexiwear K64
- https://gerrit.zephyrproject.org/r/10585 : tests: fs: Fix printf warning when using newlib
- https://gerrit.zephyrproject.org/r/10648 : clock_control: stm32: code optimization
- https://gerrit.zephyrproject.org/r/10423 : board: stm32373c_eval: enable support of LL Cube clock control driver
- https://gerrit.zephyrproject.org/r/10422 : board: nucleo_f334r8: enable support of LL Cube clock control driver
- https://gerrit.zephyrproject.org/r/10424 : boards: nucleo_l476rg: enable support of LL Cube clock control driver
- https://gerrit.zephyrproject.org/r/10420 : soc: stm32l4xx: support of Cube LL Clock driver
- https://gerrit.zephyrproject.org/r/10416 : i2c: stm32: change deprecated constant
- https://gerrit.zephyrproject.org/r/10412 : clock control:stm32: provide STM32Cube LL based driver
- https://gerrit.zephyrproject.org/r/10417 : i2c: update stm32 i2c_lx to support LL clock control driver
- https://gerrit.zephyrproject.org/r/10418 : pwm: update stm32 pwm to support LL clock control driver
- https://gerrit.zephyrproject.org/r/10470 : soc: stm32l4x: clean up after Cube LL clock control
- https://gerrit.zephyrproject.org/r/10421 : soc: stm32f3xx: support of Cube LL Clock driver
- https://gerrit.zephyrproject.org/r/10419 : flash: update stm32 flash_f3x to support LL clock control driver
- https://gerrit.zephyrproject.org/r/10472 : clock control: clean up after stm32cube LL driver
- https://gerrit.zephyrproject.org/r/10473 : drivers: stm32: clean up after stm23cube based clock control
- https://gerrit.zephyrproject.org/r/10471 : soc: stm32f3x: clean up after Cube LL clock control
- https://gerrit.zephyrproject.org/r/10192 : x86: implement direct interrupts
- https://gerrit.zephyrproject.org/r/10541 : drivers: dma_shim: update dma qmsi shim driver
- https://gerrit.zephyrproject.org/r/7738 : RFC: Add support for Device Tree
- https://gerrit.zephyrproject.org/r/10626 : RFC: DTS: Add base DTS and YAML definitions
- https://gerrit.zephyrproject.org/r/10615 : boards: stm32f4_discovery: Add new STM32 F4 Discovery boards
- https://gerrit.zephyrproject.org/r/9711 : Bluetooth: SDP: Get ProtocolDescriptorList attribute internals
- https://gerrit.zephyrproject.org/r/9716 : Bluetooth: shell: Use SupportedFeature attribute API
- https://gerrit.zephyrproject.org/r/10454 : archives: refactor archive script
- https://gerrit.zephyrproject.org/r/9717 : Bluetooth: shell: Add support to retrieve A2SRC record
- https://gerrit.zephyrproject.org/r/9714 : Bluetooth: shell: Add getting ProfileDescriptorList attribute
- https://gerrit.zephyrproject.org/r/9715 : Bluetooth: SDP: Add API to get SupportedFeature attribute
- https://gerrit.zephyrproject.org/r/9713 : Bluetooth: SDP: Add API to get ProfileDescriptorList attribute
- https://gerrit.zephyrproject.org/r/9712 : Bluetooth: shell: Add SDP client support
- https://gerrit.zephyrproject.org/r/10239 : added preliminary version of winc1500 driver and Arrow Panther support
- https://gerrit.zephyrproject.org/r/10175 : usb: cdc_acm: Use 2 instead of 4 for IN BULK endpoint
- https://gerrit.zephyrproject.org/r/10176 : usb: usb_dc_stm: Add support for STM32Cube HAL_PCD USB driver
- https://gerrit.zephyrproject.org/r/9516 : drivers: Add Atmel SAM family GMAC Ethernet driver
- https://gerrit.zephyrproject.org/r/10075 : net/mqtt: Add the MQTT Publisher sample application
- https://gerrit.zephyrproject.org/r/10646 : hexiwear_k64: Add RST board documentation
- https://gerrit.zephyrproject.org/r/10091 : net/mqtt: Add the testcase.ini file to the MQTT Publisher sample app
- https://gerrit.zephyrproject.org/r/10093 : samples/net/http: Add the server sample application
- https://gerrit.zephyrproject.org/r/10623 : kernel: add k_poll() API
- https://gerrit.zephyrproject.org/r/9762 : CI: rearchitect with a framework that orchestrates running
- https://gerrit.zephyrproject.org/r/10619 : kernel: add k_fifo_is_empty()
- https://gerrit.zephyrproject.org/r/10622 : kernel: add _WAIT_Q_INIT()
- https://gerrit.zephyrproject.org/r/10621 : kernel: add _THREAD_POLLING thread state
- https://gerrit.zephyrproject.org/r/10620 : kernel: add _is_thread_state_set()
- https://gerrit.zephyrproject.org/r/10624 : tests: add poll kernel test
- https://gerrit.zephyrproject.org/r/10595 : arm: cmsis: Convert _ScbDivByZeroFaultEnable to use direct CMSIS register access
- https://gerrit.zephyrproject.org/r/10596 : arm: cmsis: Convert _Scb*FaultIs* & _ScbIs*Fault to use CMSIS register access
- https://gerrit.zephyrproject.org/r/10605 : arm: cmsis: cleanup use of _SCS_CPACR_CP1{0,1}_Pos define
- https://gerrit.zephyrproject.org/r/10591 : arm: cmsis: Convert _ScbIsNestedExc to use direct CMSIS register access
- https://gerrit.zephyrproject.org/r/10599 : arm: cmsis: Convert _ClearFaults to use direct CMSIS register access
- https://gerrit.zephyrproject.org/r/10594 : arm: cmsis: Convert _ScbHardFaultIsForced to use direct CMSIS register access
- https://gerrit.zephyrproject.org/r/10597 : arm: cmsis: Convert _Scb*FaultAddrGet to use direct CMSIS register access
- https://gerrit.zephyrproject.org/r/10601 : arm: cmsis: Remove last bits of scs/scb as we've converted to CMSIS
- https://gerrit.zephyrproject.org/r/10600 : arm: cmsis: Convert _Scb*Fault*Reset to use direct CMSIS register access
- https://gerrit.zephyrproject.org/r/10592 : arm: cmsis: Convert FaultEnable to use direct CMSIS register access
- https://gerrit.zephyrproject.org/r/10598 : arm: cmsis: Convert printing of MMFSR, BFSR, and UFSR to CMSIS
- https://gerrit.zephyrproject.org/r/10593 : arm: cmsis: Convert _ScbActiveVectorGet to use direct CMSIS register access
- https://gerrit.zephyrproject.org/r/9977 : samples: net: "Mini HTTP" example & validator for TCP layer
- https://gerrit.zephyrproject.org/r/10613 : soc: stm32f4xx: Make missing flash latency info a compile error
- https://gerrit.zephyrproject.org/r/10612 : soc: stm32f4xx: Document the flash latency values

MERGED within last 24 hours:
- https://gerrit.zephyrproject.org/r/10662 : tests: kernel: import irq_offload test from legacy
- https://gerrit.zephyrproject.org/r/10664 : net: tcp: Only return -ETIMEDOUT if timeout!=0 in connect
- https://gerrit.zephyrproject.org/r/10655 : samples/zoap_server: Add a 802.15.4 case to the test suite
- https://gerrit.zephyrproject.org/r/10661 : doc: fix .rst headings in new sample docs
- https://gerrit.zephyrproject.org/r/10658 : toolchain: define DTC for zephyr SDK
- https://gerrit.zephyrproject.org/r/10649 : Bluetooth: Fix trivial coding style issue
- https://gerrit.zephyrproject.org/r/10652 : Merge arm branch into master
- https://gerrit.zephyrproject.org/r/10651 : Revert "Revert "sanitycheck: add support for risc v boards""
- https://gerrit.zephyrproject.org/r/10642 : samples: zperf: Enable TCP for zperf configuration
- https://gerrit.zephyrproject.org/r/10641 : samples: zperf: Use native IP stack for TCP support
- https://gerrit.zephyrproject.org/r/10459 : samples: net: irc_bot: add DNS support
- https://gerrit.zephyrproject.org/r/10460 : samples: net: irc_bot: add DHCPv4 support
- https://gerrit.zephyrproject.org/r/10396 : samples: net: irc_bot: add FRDM K64F project .conf
- https://gerrit.zephyrproject.org/r/10458 : samples: net: irc_bot: add IPv4 support
- https://gerrit.zephyrproject.org/r/10395 : samples: net: irc_bot: add Linaro copyright
- https://gerrit.zephyrproject.org/r/10394 : samples: net: irc_bot: handle messages across multiple fragments
- https://gerrit.zephyrproject.org/r/10378 : samples: net: irc_bot: run sample process as a thread
- https://gerrit.zephyrproject.org/r/10397 : samples: net: Add IRC bot example
- https://gerrit.zephyrproject.org/r/10379 : samples: net: irc_bot: establish privmsg callback typedef
- https://gerrit.zephyrproject.org/r/10380 : samples: net: irc_bot: release net_context reference upon error
- https://gerrit.zephyrproject.org/r/10381 : samples: net: irc_bot: remove unneeded typecasts and extra var
- https://gerrit.zephyrproject.org/r/10382 : samples: net: irc_bot: add helper function in_addr_set()
- https://gerrit.zephyrproject.org/r/10383 : samples: net: irc_bot: remove sockaddr globals
- https://gerrit.zephyrproject.org/r/10384 : samples: net: irc_bot: make panic() more accessible
- https://gerrit.zephyrproject.org/r/10385 : samples: net: irc_bot: use #defines for server and port
- https://gerrit.zephyrproject.org/r/10386 : samples: net: irc_bot: make some functions more accessible
- https://gerrit.zephyrproject.org/r/10387 : samples: net: irc_bot: simplify connect path
- https://gerrit.zephyrproject.org/r/10388 : samples: net: irc_bot: expand some char buffers
- https://gerrit.zephyrproject.org/r/10389 : samples: net: irc_bot: fix null pointer deref
- https://gerrit.zephyrproject.org/r/10390 : samples: net: irc_bot: use irc parameter's connection
- https://gerrit.zephyrproject.org/r/10391 : samples: net: irc_bot: dont hardcode NET_SYS_LOG_LEVEL
- https://gerrit.zephyrproject.org/r/10392 : samples: net: irc_bot: modify disco check in on_context_recv()
- https://gerrit.zephyrproject.org/r/10393 : samples: net: irc_bot: create semi-unique IRC user names
- https://gerrit.zephyrproject.org/r/10531 : net: tcp: Clean up net_context lifecycle
- https://gerrit.zephyrproject.org/r/10533 : net: tcp: Clean up FIN handling
- https://gerrit.zephyrproject.org/r/10571 : net: net_context: Drop callbacks in net_context_put()
- https://gerrit.zephyrproject.org/r/10532 : net: tcp: Don't send active close FIN packets synchronously
- https://gerrit.zephyrproject.org/r/10572 : net: tcp: Add optional TIME_WAIT support
- https://gerrit.zephyrproject.org/r/10553 : samples/net: Add a simple telnet sample
- https://gerrit.zephyrproject.org/r/10524 : samples/zoap_server: Allow overriding the BOARD variable
- https://gerrit.zephyrproject.org/r/10405 : net: tcp: Only return -ETIMEDOUT if timeout>0 in connect
- https://gerrit.zephyrproject.org/r/10634 : net: Increasing the default number of network contexts
- https://gerrit.zephyrproject.org/r/10636 : Bluetooth: hci_core: Use nRF5x FICR address
- https://gerrit.zephyrproject.org/r/9933 : tests: benchmark: sys_kernel: Porting to unified
- https://gerrit.zephyrproject.org/r/9980 : tests: include: Move timestamp.h into common location
- https://gerrit.zephyrproject.org/r/8922 : scripts: Add device tree parser script
- https://gerrit.zephyrproject.org/r/10588 : i2c: Can pass IRQ vector constant to irq_enable
- https://gerrit.zephyrproject.org/r/10643 : Xtensa port: Removed compiler warnings about printf formats/arguments mismatch.
- https://gerrit.zephyrproject.org/r/10566 : Xtensa port: Let xcc specific make file override unsupported -Og with -O0.
- https://gerrit.zephyrproject.org/r/10640 : net/mqtt: Check function return value
- https://gerrit.zephyrproject.org/r/10637 : net: tests: Add unit tests for net_addr_pton() utils function
- https://gerrit.zephyrproject.org/r/10638 : net: utils: Add net_addr_ntop() helper function
- https://gerrit.zephyrproject.org/r/10639 : net: tests: Add unit tests for net_addr_ntop() utils function


Re: [devel] Re: Re: Re: Re: Re: Re: Re: Re: Re: Re: "/samples/net/coap_server" example is not working on "nrf52_pca10040" board

Carles Cufi
 

Hi Raju,

-----Original Message-----
From: Appala Raju [mailto:raju.ga@gmail.com]
Sent: Monday, January 23, 2017 18:39
To: devel@lists.zephyrproject.org
Subject: [devel] Re: Re: Re: Re: Re: Re: Re: Re: Re: Re:
"/samples/net/coap_server" example is not working on "nrf52_pca10040"
board

As per this post "https://devzone.nordicsemi.com/question/6566/how-to-
get-6-byte-mac-address-at-nrf51822/" we can have unique Mac address but
it seems this is not mapped in this OS properly. Can we implement the
same.
We can indeed. Here's a gerrit patch for it, feel free to try it out:

https://gerrit.zephyrproject.org/r/#/c/10636/

Thanks,

Carles


Daily Gerrit Digest

donotreply@...
 

NEW within last 24 hours:
- https://gerrit.zephyrproject.org/r/10648 : clock_control: stm32: code optimization
- https://gerrit.zephyrproject.org/r/10645 : Bluetooth: HFP HF: Handling AG Network error
- https://gerrit.zephyrproject.org/r/10647 : DRAFT doc: net: Migrate from Zephyr 1.6 to 1.7
- https://gerrit.zephyrproject.org/r/10615 : boards: stm32f407_discovery: Add new STM32F407VG based board
- https://gerrit.zephyrproject.org/r/10639 : net: tests: Add unit tests for net_addr_ntop() utils function
- https://gerrit.zephyrproject.org/r/10638 : net: utils: Add net_addr_ntop() helper function
- https://gerrit.zephyrproject.org/r/10646 : hexiwear_k64: Add RST board documentation
- https://gerrit.zephyrproject.org/r/10644 : Bluetooth: HFP HF: Remove unused variable 'buf'
- https://gerrit.zephyrproject.org/r/10643 : Xtensa port: Removed compiler warnings about printf formats/arguments mismatch.
- https://gerrit.zephyrproject.org/r/10642 : samples: zperf: Enable TCP for zperf configuration
- https://gerrit.zephyrproject.org/r/10641 : samples: zperf: Use native IP stack for TCP support
- https://gerrit.zephyrproject.org/r/10637 : net: tests: Add unit tests for net_addr_pton() utils function
- https://gerrit.zephyrproject.org/r/10640 : net/mqtt: Check function return value
- https://gerrit.zephyrproject.org/r/10636 : bluetooth: hci_core: Use nRF5x FICR address
- https://gerrit.zephyrproject.org/r/10623 : kernel: add k_poll() API
- https://gerrit.zephyrproject.org/r/10619 : kernel: add k_fifo_is_empty()
- https://gerrit.zephyrproject.org/r/10616 : boards: stm32f401_discovery: Add new STM32F401VC based board
- https://gerrit.zephyrproject.org/r/10634 : net: Increasing the default number of network contexts
- https://gerrit.zephyrproject.org/r/10633 : samples/drivers: STM32F4x flash
- https://gerrit.zephyrproject.org/r/10632 : flash/stm32: driver for STM32F4x series
- https://gerrit.zephyrproject.org/r/10631 : include/misc: binary search algorithm
- https://gerrit.zephyrproject.org/r/10629 : RFC: DTS: Kinetis: Add support for Hexiwear K64
- https://gerrit.zephyrproject.org/r/10630 : RFC: DTS: Remove unnecesary MCUX definitions
- https://gerrit.zephyrproject.org/r/10627 : RFC: DTS: Kinetis: Add base support for Kinetis
- https://gerrit.zephyrproject.org/r/10628 : RFC: DTS: Kinetis: Add FRDM_K64F support
- https://gerrit.zephyrproject.org/r/10626 : RFC: DTS: Add base DTS and YAML definitions
- https://gerrit.zephyrproject.org/r/10625 : samples/net/http: Add the HTTP client sample application
- https://gerrit.zephyrproject.org/r/10624 : tests: add poll kernel test
- https://gerrit.zephyrproject.org/r/10622 : kernel: add _WAIT_Q_INIT()
- https://gerrit.zephyrproject.org/r/10620 : kernel: add _is_thread_state_set()
- https://gerrit.zephyrproject.org/r/10621 : kernel: add _THREAD_POLLING thread state
- https://gerrit.zephyrproject.org/r/10618 : Add hashicorp's packer binary to basebuild

UPDATED within last 24 hours:
- https://gerrit.zephyrproject.org/r/10421 : soc: stm32f3xx: support of Cube LL Clock driver
- https://gerrit.zephyrproject.org/r/10423 : board: stm32373c_eval: enable support of LL Cube clock control driver
- https://gerrit.zephyrproject.org/r/10424 : boards: nucleo_l476rg: enable support of LL Cube clock control driver
- https://gerrit.zephyrproject.org/r/10422 : board: nucleo_f334r8: enable support of LL Cube clock control driver
- https://gerrit.zephyrproject.org/r/10418 : pwm: update stm32 pwm to support LL clock control driver
- https://gerrit.zephyrproject.org/r/10417 : i2c: update stm32 i2c_lx to support LL clock control driver
- https://gerrit.zephyrproject.org/r/10419 : flash: update stm32 flash_f3x to support LL clock control driver
- https://gerrit.zephyrproject.org/r/10420 : soc: stm32l4xx: support of Cube LL Clock driver
- https://gerrit.zephyrproject.org/r/10416 : i2c: stm32: change deprecated constant
- https://gerrit.zephyrproject.org/r/10415 : uart: update stm32 uart to support LL clock control driver
- https://gerrit.zephyrproject.org/r/10414 : pinmux: update stm32 pinmux to support LL clock control driver
- https://gerrit.zephyrproject.org/r/10471 : soc: stm32f3x: clean up after Cube LL clock control
- https://gerrit.zephyrproject.org/r/10412 : clock control:stm32: provide STM32Cube LL based driver
- https://gerrit.zephyrproject.org/r/10413 : gpio: update stm32 gpio to support LL clock control driver
- https://gerrit.zephyrproject.org/r/10470 : soc: stm32l4x: clean up after Cube LL clock control
- https://gerrit.zephyrproject.org/r/10473 : drivers: stm32: clean up after stm23cube based clock control
- https://gerrit.zephyrproject.org/r/10472 : clock control: clean up after stm32cube LL driver
- https://gerrit.zephyrproject.org/r/9715 : Bluetooth: SDP: Add API to get SupportedFeature attribute
- https://gerrit.zephyrproject.org/r/10613 : soc: stm32f4xx: Make missing flash latency info a compile error
- https://gerrit.zephyrproject.org/r/10306 : soc: stm32f4xx: Add STM32F401xC, STM32F405xG and STM32F407xG
- https://gerrit.zephyrproject.org/r/9714 : Bluetooth: shell: Add getting ProfileDescriptorList attribute
- https://gerrit.zephyrproject.org/r/9712 : Bluetooth: shell: Add SDP client support
- https://gerrit.zephyrproject.org/r/10547 : Bluetooth: HFP HF: Disconnect rfcomm on SLC error
- https://gerrit.zephyrproject.org/r/10612 : soc: stm32f4xx: Document the flash latency values
- https://gerrit.zephyrproject.org/r/9711 : Bluetooth: SDP: Get ProtocolDescriptorList attribute internals
- https://gerrit.zephyrproject.org/r/10546 : Bluetooth: HFP HF: Indicate disconnect to application
- https://gerrit.zephyrproject.org/r/10426 : Bluetooth: HFP HF: Enable extended AG Error Result Code
- https://gerrit.zephyrproject.org/r/10479 : Bluetooth: HFP HF: Service level connection completed
- https://gerrit.zephyrproject.org/r/7738 : RFC: Add support for Device Tree
- https://gerrit.zephyrproject.org/r/10585 : tests: fs: Fix printf warning when using newlib
- https://gerrit.zephyrproject.org/r/10176 : usb: usb_dc_stm: Add support for STM32Cube HAL_PCD USB driver
- https://gerrit.zephyrproject.org/r/10093 : samples/net/http: Add the server sample application
- https://gerrit.zephyrproject.org/r/10091 : net/mqtt: Add the testcase.ini file to the MQTT Publisher sample app
- https://gerrit.zephyrproject.org/r/10607 : net/mqtt: Validate null or app level zero-length rx buffers
- https://gerrit.zephyrproject.org/r/10074 : net/mqtt: Add the "malformed" callback to the MQTT ctx structure
- https://gerrit.zephyrproject.org/r/9517 : samples: net: echo_server .conf for Atmel SMART SAM E70 Xplained board
- https://gerrit.zephyrproject.org/r/10553 : samples/net: Add a simple telnet sample
- https://gerrit.zephyrproject.org/r/10531 : net: tcp: Clean up net_context lifecycle
- https://gerrit.zephyrproject.org/r/9977 : samples: net: "Mini HTTP" example & validator for TCP layer
- https://gerrit.zephyrproject.org/r/10524 : samples/zoap_server: Allow overriding the BOARD variable
- https://gerrit.zephyrproject.org/r/9460 : Bluetooth: AVDTP: Add AVDTP Discover Function Definition
- https://gerrit.zephyrproject.org/r/9663 : Bluetooth: AVDTP: Add AVDTP Receive Function
- https://gerrit.zephyrproject.org/r/10260 : samples/net/http: Update README file
- https://gerrit.zephyrproject.org/r/8922 : scripts: Add device tree parser script
- https://gerrit.zephyrproject.org/r/10075 : net/mqtt: Add the MQTT Publisher sample application
- https://gerrit.zephyrproject.org/r/10454 : archives: refactor archive script
- https://gerrit.zephyrproject.org/r/10175 : usb: cdc_acm: Use endpoint 2 instead of endpoint 4 for IN BULK endpoint
- https://gerrit.zephyrproject.org/r/10259 : samples/net/http: Add HTTP 4xx class of status code
- https://gerrit.zephyrproject.org/r/10190 : samples/net/http: Move http write functionality to its own files
- https://gerrit.zephyrproject.org/r/10218 : samples/net/http: Increase the max number of network contexts
- https://gerrit.zephyrproject.org/r/10220 : samples/net/http: Modify data pool size
- https://gerrit.zephyrproject.org/r/10178 : samples/net/http: Introduce routines to handle multiple contexts
- https://gerrit.zephyrproject.org/r/10258 : samples/net/http: Add support for multiple URLs

MERGED within last 24 hours:
- https://gerrit.zephyrproject.org/r/10559 : net: bt: Fix failing to resolve link-local address
- https://gerrit.zephyrproject.org/r/10578 : samples: webusb: fix type of bytes_read
- https://gerrit.zephyrproject.org/r/10577 : usb: Change transfer_len type to int32_t in usb_request_handler typedef
- https://gerrit.zephyrproject.org/r/10579 : fat: match type info expected by fat library for f_write
- https://gerrit.zephyrproject.org/r/10576 : samples: zperf: cleanup types for constant arrays
- https://gerrit.zephyrproject.org/r/8874 : driver: ethernet: Fix typo on enc28j60 driver Kconfig
- https://gerrit.zephyrproject.org/r/10563 : samples/net: Fix a tiny mistake in dhcpv4_client README.rst
- https://gerrit.zephyrproject.org/r/10574 : net: echo_server: Enable TCP for frdm_k64f.
- https://gerrit.zephyrproject.org/r/10567 : net: ip: stat: fix typo in rpl.dio.sent stat
- https://gerrit.zephyrproject.org/r/10525 : samples/zoap_server: Enable support for 802.15.4
- https://gerrit.zephyrproject.org/r/10436 : net: correct in*_addr parameter of net_addr_pton()
- https://gerrit.zephyrproject.org/r/10557 : net: tcp: Call connect callback later


Re: [devel] Zephyr SDK 0.9 released

Paul Sokolovsky
 

Hello,

On Wed, 25 Jan 2017 20:47:22 +0000
"Nashif, Anas" <anas.nashif@intel.com> wrote:

Hi,

Zephyr SDK 0.9 is released and available for download.

Release notes:

https://www.zephyrproject.org/content/zephyr-project-software-development-kit-sdk-09

Download:

https://www.zephyrproject.org/downloads/tools
Based on md5sum, that's the same file as had been announced a week
before. So, people who downloaded it may check their md5 and save some
traffic.

Regards,
Anas


--
Best Regards,
Paul

Linaro.org | Open source software for ARM SoCs
Follow Linaro: http://www.facebook.com/pages/Linaro
http://twitter.com/#!/linaroorg - http://www.linaro.org/linaro-blog


STM32F4 USB device controller driver

Christer Weinigel
 

Hi all,

I've updated my USB driver a bit and I hope that I haven't forgotten to
address any of the review comments.

Since I've been testing this on my own STM32F405VG based board that
nobody else has access to I didn't have any good place in Zephyr to show
how to use the USB driver. But I dug around in my boxes of junk and
found two STM32F4 Discovery boards, one with a STM32F407VG on it and
another one with a STM32F401VC. I've added support for all the above
MCUs, and then support for the two Discovery boards. With this in place
I have a patch with my USB driver which then shows how to get a USB
console on both boards.

Some changes to flash_registers.h:

https://gerrit.zephyrproject.org/r/#/c/10612/
https://gerrit.zephyrproject.org/r/#/c/10613/

STM32F401xC, STM32F405xG, STM32F407xG support:

https://gerrit.zephyrproject.org/r/#/c/10306/

Discovery Board definitions:

https://gerrit.zephyrproject.org/r/#/c/10615/
https://gerrit.zephyrproject.org/r/#/c/10616/

Finally the USB stuff:

https://gerrit.zephyrproject.org/r/#/c/10175/
https://gerrit.zephyrproject.org/r/#/c/10176/7

Please take a look if you have the time.

/Christer


Daily Gerrit Digest

donotreply@...
 

NEW within last 24 hours:
- https://gerrit.zephyrproject.org/r/10614 : soc: stm32f4xx: Add flash latency configuration for STM32F405xG
- https://gerrit.zephyrproject.org/r/10613 : soc: stm32f4xx: Make missing flash latency information a compile error
- https://gerrit.zephyrproject.org/r/10612 : soc: stm32f4xx: Document the flash latency values
- https://gerrit.zephyrproject.org/r/10607 : net/mqtt: Validate null or app level zero-length rx buffers
- https://gerrit.zephyrproject.org/r/10605 : arm: cmsis: cleanup use of _SCS_CPACR_CP1{0,1}_Pos define

UPDATED within last 24 hours:
- https://gerrit.zephyrproject.org/r/7738 : RFC: Add support for Device Tree
- https://gerrit.zephyrproject.org/r/10091 : net/mqtt: Add the testcase.ini file to the MQTT Publisher sample app
- https://gerrit.zephyrproject.org/r/10075 : net/mqtt: Add the MQTT Publisher sample application
- https://gerrit.zephyrproject.org/r/10074 : net/mqtt: Add the "malformed" callback to the MQTT ctx structure
- https://gerrit.zephyrproject.org/r/10073 : net/mqtt: Simplify the MQTT high-level API
- https://gerrit.zephyrproject.org/r/10072 : net/mqtt: Move upwards buffer size validation
- https://gerrit.zephyrproject.org/r/10572 : net: tcp: Add optional TIME_WAIT support
- https://gerrit.zephyrproject.org/r/10571 : net: net_context: Drop callbacks in net_context_put()
- https://gerrit.zephyrproject.org/r/10533 : net: tcp: Clean up FIN handling
- https://gerrit.zephyrproject.org/r/10532 : net: tcp: Don't send active close FIN packets synchronously
- https://gerrit.zephyrproject.org/r/10531 : net: tcp: Clean up net_context lifecycle
- https://gerrit.zephyrproject.org/r/10436 : net: correct in*_addr parameter of net_addr_pton()
- https://gerrit.zephyrproject.org/r/10512 : doc: update copyright for documentation
- https://gerrit.zephyrproject.org/r/10601 : arm: cmsis: Remove last bits of scs/scb as we've converted to CMSIS
- https://gerrit.zephyrproject.org/r/10566 : Xtensa port: Let xcc specific make file override unsupported -Og with -O0.
- https://gerrit.zephyrproject.org/r/10600 : arm: cmsis: Convert _Scb*Fault*Reset to use direct CMSIS register access
- https://gerrit.zephyrproject.org/r/10599 : arm: cmsis: Convert _ClearFaults to use direct CMSIS register access
- https://gerrit.zephyrproject.org/r/10598 : arm: cmsis: Convert printing of MMFSR, BFSR, and UFSR to CMSIS
- https://gerrit.zephyrproject.org/r/10597 : arm: cmsis: Convert _Scb*FaultAddrGet to use direct CMSIS register access
- https://gerrit.zephyrproject.org/r/10596 : arm: cmsis: Convert _Scb*FaultIs* & _ScbIs*Fault to use CMSIS register access
- https://gerrit.zephyrproject.org/r/10594 : arm: cmsis: Convert _ScbHardFaultIsForced to use direct CMSIS register access
- https://gerrit.zephyrproject.org/r/10595 : arm: cmsis: Convert _ScbDivByZeroFaultEnable to use direct CMSIS register access

MERGED within last 24 hours:
- https://gerrit.zephyrproject.org/r/10590 : doc: update menuconfig images in application doc
- https://gerrit.zephyrproject.org/r/10564 : Merge net branch into master
- https://gerrit.zephyrproject.org/r/10604 : Merge bluetooth branch into master


Daily Gerrit Digest

donotreply@...
 

NEW within last 24 hours:
- https://gerrit.zephyrproject.org/r/10585 : tests: fs: Fix printf warning when using newlib
- https://gerrit.zephyrproject.org/r/10604 : Merge bluetooth branch into master
- https://gerrit.zephyrproject.org/r/10594 : arm: cmsis: Convert _ScbHardFaultIsForced to use direct CMSIS register access
- https://gerrit.zephyrproject.org/r/10595 : arm: cmsis: Convert _ScbDivByZeroFaultEnable to use direct CMSIS register access
- https://gerrit.zephyrproject.org/r/10596 : arm: cmsis: Convert _Scb*FaultIs* & _ScbIs*Fault to use CMSIS register access
- https://gerrit.zephyrproject.org/r/10599 : arm: cmsis: Convert _ClearFaults to use direct CMSIS register access
- https://gerrit.zephyrproject.org/r/10601 : arm: cmsis: Remove last bits of scs/scb as we've converted to CMSIS
- https://gerrit.zephyrproject.org/r/10600 : arm: cmsis: Convert _Scb*Fault*Reset to use direct CMSIS register access
- https://gerrit.zephyrproject.org/r/10593 : arm: cmsis: Convert _ScbActiveVectorGet to use direct CMSIS register access
- https://gerrit.zephyrproject.org/r/10592 : arm: cmsis: Convert FaultEnable to use direct CMSIS register access
- https://gerrit.zephyrproject.org/r/10597 : arm: cmsis: Convert _Scb*FaultAddrGet to use direct CMSIS register access
- https://gerrit.zephyrproject.org/r/10598 : arm: cmsis: Convert printing of MMFSR, BFSR, and UFSR to CMSIS
- https://gerrit.zephyrproject.org/r/10591 : arm: cmsis: Convert _ScbIsNestedExc to use direct CMSIS register access
- https://gerrit.zephyrproject.org/r/10590 : doc: update menuconfig images in application doc
- https://gerrit.zephyrproject.org/r/10589 : ext: Add missing header files symbols for Atmel SAM E70
- https://gerrit.zephyrproject.org/r/10586 : doc: add CSS support for hlist directive
- https://gerrit.zephyrproject.org/r/10588 : i2c: Can pass IRQ vector constant to irq_enable
- https://gerrit.zephyrproject.org/r/10579 : fat: match type info expected by fat library for f_write
- https://gerrit.zephyrproject.org/r/10577 : usb: Change transfer_len type to int32_t in usb_request_handler typedef
- https://gerrit.zephyrproject.org/r/10578 : samples: webusb: fix type of bytes_read
- https://gerrit.zephyrproject.org/r/10566 : Xtensa port: Let xcc specific make file override unsupported -Og with -O1.
- https://gerrit.zephyrproject.org/r/10571 : net: net_context: Drop callbacks in net_context_put()
- https://gerrit.zephyrproject.org/r/10575 : doc: remove artifacts of doc build recently added
- https://gerrit.zephyrproject.org/r/10576 : samples: zperf: cleanup types for constant arrays
- https://gerrit.zephyrproject.org/r/10574 : net: echo_server: Enable TCP for frdm_k64f.
- https://gerrit.zephyrproject.org/r/10572 : net: tcp: Add optional TIME_WAIT support
- https://gerrit.zephyrproject.org/r/10573 : tests: kernel: import floating point sharing tests to unified
- https://gerrit.zephyrproject.org/r/10567 : net: ip: stat: fix typo in rpl.dio.sent stat
- https://gerrit.zephyrproject.org/r/10565 : cov-csv.py: support uploading data to a Google Sheet

UPDATED within last 24 hours:
- https://gerrit.zephyrproject.org/r/10512 : doc: update copyright for documentation
- https://gerrit.zephyrproject.org/r/9980 : tests: include: Move timestamp.h into common location
- https://gerrit.zephyrproject.org/r/10183 : irq: introduce 'direct' interrupt API definition
- https://gerrit.zephyrproject.org/r/10479 : Bluetooth: HFP HF: Service level connection completed
- https://gerrit.zephyrproject.org/r/9460 : Bluetooth: AVDTP: Add AVDTP Discover Function Definition
- https://gerrit.zephyrproject.org/r/10294 : drivers: Add Atmel SAM DAC (DACC) driver
- https://gerrit.zephyrproject.org/r/6128 : drivers: Add basic Atmel SAM USART driver
- https://gerrit.zephyrproject.org/r/10293 : DONT MERGE drivers: Add DAC driver API
- https://gerrit.zephyrproject.org/r/10290 : drivers: Add Atmel SAM DMA (XDMAC) driver
- https://gerrit.zephyrproject.org/r/9517 : samples: net: echo_server .conf for Atmel SMART SAM E70 Xplained board
- https://gerrit.zephyrproject.org/r/6127 : arch: Add pmc, gpio internal Atmel SAM drivers
- https://gerrit.zephyrproject.org/r/10291 : drivers: Add Atmel SAM Timer Counter (TC) driver
- https://gerrit.zephyrproject.org/r/9516 : drivers: Add Atmel SAM family GMAC Ethernet driver
- https://gerrit.zephyrproject.org/r/10292 : drivers: Add DAC driver infrastructure
- https://gerrit.zephyrproject.org/r/5028 : boards: Add Atmel SAM E70 Xplained board support
- https://gerrit.zephyrproject.org/r/6662 : ext: Add Atmel SAM3X header files from Atmel ASF library
- https://gerrit.zephyrproject.org/r/9515 : arch: Add support for Atmel SAM E70 SoC configuration at boot
- https://gerrit.zephyrproject.org/r/5025 : ext: Add Atmel SAM E70 header files from Atmel ASF library
- https://gerrit.zephyrproject.org/r/5027 : arch: Add Atmel SAM E70 SoC support
- https://gerrit.zephyrproject.org/r/10093 : samples/net/http: Add the server sample application
- https://gerrit.zephyrproject.org/r/10489 : api: dma: dma api update
- https://gerrit.zephyrproject.org/r/10412 : clock control:stm32: provide STM32Cube LL based driver
- https://gerrit.zephyrproject.org/r/8922 : scripts: Add device tree parser script
- https://gerrit.zephyrproject.org/r/10531 : net: tcp: Clean up net_context lifecycle
- https://gerrit.zephyrproject.org/r/10532 : net: tcp: Don't send active close FIN packets synchronously
- https://gerrit.zephyrproject.org/r/10369 : ataes132a: Adds a driver to support ATAES132A device
- https://gerrit.zephyrproject.org/r/10533 : net: tcp: Clean up FIN handling
- https://gerrit.zephyrproject.org/r/10257 : samples: grove: use correct i2c device driver name
- https://gerrit.zephyrproject.org/r/9977 : samples: net: "Mini HTTP" example & validator for TCP layer
- https://gerrit.zephyrproject.org/r/9762 : CI: rearchitect with a framework that orchestrates running
- https://gerrit.zephyrproject.org/r/10557 : net: tcp: Call connect callback later
- https://gerrit.zephyrproject.org/r/10563 : samples/net: Fix a tiny mistake in dhcpv4_client README.rst
- https://gerrit.zephyrproject.org/r/10553 : samples/net: Add a simple telnet sample
- https://gerrit.zephyrproject.org/r/10423 : board: stm32373c_eval: enable support of LL Cube clock control driver
- https://gerrit.zephyrproject.org/r/10424 : boards: nucleo_l476rg: enable support of LL Cube clock control driver
- https://gerrit.zephyrproject.org/r/10419 : flash: update stm32 flash_f3x to support LL clock control driver
- https://gerrit.zephyrproject.org/r/10416 : i2c: stm32: change deprecated constant
- https://gerrit.zephyrproject.org/r/10415 : uart: update stm32 uart to support LL clock control driver
- https://gerrit.zephyrproject.org/r/10414 : pinmux: update stm32 pinmux to support LL clock control driver
- https://gerrit.zephyrproject.org/r/10421 : soc: stm32f3xx: support of Cube LL Clock driver
- https://gerrit.zephyrproject.org/r/10470 : soc: stm32l4x: clean up after Cube LL clock control
- https://gerrit.zephyrproject.org/r/10413 : gpio: update stm32 gpio to support LL clock control driver
- https://gerrit.zephyrproject.org/r/10422 : board: nucleo_f334r8: enable support of LL Cube clock control driver
- https://gerrit.zephyrproject.org/r/10472 : clock control: clean up after stm32cube LL driver
- https://gerrit.zephyrproject.org/r/10418 : pwm: update stm32 pwm to support LL clock control driver
- https://gerrit.zephyrproject.org/r/10420 : soc: stm32l4xx: support of Cube LL Clock driver
- https://gerrit.zephyrproject.org/r/10417 : i2c: update stm32 i2c_lx to support LL clock control driver
- https://gerrit.zephyrproject.org/r/10473 : drivers: stm32: clean up after stm23cube based clock control
- https://gerrit.zephyrproject.org/r/10471 : soc: stm32f3x: clean up after Cube LL clock control
- https://gerrit.zephyrproject.org/r/10559 : net: bt: Fix failing to resolve link-local address
- https://gerrit.zephyrproject.org/r/9856 : drivers: gpio: stm32: Fix build error on stm32f1x/4x for ports F/G/H
- https://gerrit.zephyrproject.org/r/10564 : Merge net branch into master

MERGED within last 24 hours:
- https://gerrit.zephyrproject.org/r/10583 : Bluetooth: SPI: retry spi_transceive calls if invalid
- https://gerrit.zephyrproject.org/r/10602 : Bluetooth: SPI: Disable IRQ pin callback to avoid spurious IRQs
- https://gerrit.zephyrproject.org/r/10582 : Bluetooth: SPI: fix max SPI buffer length
- https://gerrit.zephyrproject.org/r/10581 : Bluetooth: SPI: fix Kconfig SPI IRQ PIN description
- https://gerrit.zephyrproject.org/r/10580 : Bluetooth: hci_raw: Make bt_buf_get_rx args consistent
- https://gerrit.zephyrproject.org/r/10570 : Xtensa port: _thread_entry shall use call4 to start the thread.
- https://gerrit.zephyrproject.org/r/10569 : Xtensa port: Replaced call to legacy sys_thread_self_get by one to k_current_get
- https://gerrit.zephyrproject.org/r/10568 : Xtensa port: Fixed assembly comments to be accurate with code.
- https://gerrit.zephyrproject.org/r/10543 : Bluetooth: SPI: switch to a single SPI transfer when receiving
- https://gerrit.zephyrproject.org/r/10544 : Bluetooth: SPI: introduce CONFIG_BLUETOOTH_SPI_BLUENRG
- https://gerrit.zephyrproject.org/r/10505 : doc: update template for nucleo_f401re board
- https://gerrit.zephyrproject.org/r/10476 : board: add nucleo_411re board documentation
- https://gerrit.zephyrproject.org/r/10515 : Xtensa port: Added support for Xtensa internal timer as system timer.
- https://gerrit.zephyrproject.org/r/10536 : Changed Kbuild to pass also KBUILD_CPPFLAGS to CC on addition to KBUILD_CFLAGS.
- https://gerrit.zephyrproject.org/r/10507 : sensor: use SENSOR_CHAN_*_XYZ instead of SENSOR_CHAN_*_ANY
- https://gerrit.zephyrproject.org/r/10529 : tests: context: Verify for out of bounds array
- https://gerrit.zephyrproject.org/r/10551 : Xtensa port: Changed simulation support with xt-run/xtsc-run to be qemu like.
- https://gerrit.zephyrproject.org/r/10537 : Xtensa port: Define __builtin_unreachable() as CLI macro when using XCC.
- https://gerrit.zephyrproject.org/r/10323 : Xtensa port: Added linker script for several Xtensa cores.
- https://gerrit.zephyrproject.org/r/10516 : sensor: add SENSOR_CHAN_*_XYZ enum values
- https://gerrit.zephyrproject.org/r/10484 : arm: cmsis: Convert _ScbIsInThreadMode to use direct CMSIS register access
- https://gerrit.zephyrproject.org/r/10483 : arm: cmsis: Convert _ScbPendsvSet to use direct CMSIS register access
- https://gerrit.zephyrproject.org/r/10482 : arm: cmsis: Convert _ScbNmiPend to use direct CMSIS register access
- https://gerrit.zephyrproject.org/r/10481 : arm: refactor clearing of exception faults to common code
- https://gerrit.zephyrproject.org/r/10485 : arm: scb: Move SCB asm defines into cpu_idle.S


A friendly reminder about the issue types used in Zephyr's Jira projects

Linkmeyer, Mark J <mark.j.linkmeyer@...>
 

Hi.

It's been noticed recently that Zephyr users and developers are not always creating issues in Jira using the correct issue types. Please take a moment to refresh your memory on the differences between epics, stories, tasks, and bugs by reviewing their descriptions on this Jira help page: https://wiki.zephyrproject.org/view/Jira_Usage_Help. Also, please note that we've recently split out Zephyr SDK and Zephyr Infrastructure into their own separate Jira projects. This is also mentioned in the Jira help page.

If you have any questions, please let me know.

Thanks,
Mark

Mark Linkmeyer
Intel Corporation
Open Source Technology Center--> Zephyr(tm) Software Project Manager

Confidentiality Notice: This e-mail message, including any attachments, is for the sole use of the intended recipient(s) and may contain confidential and/or attorney-client privileged information. Any unauthorized review; use, disclosure or distribution is prohibited. If you are not the intended recipient, please contact the sender immediately by reply e-mail and destroy all copies of the original message.


Daily Gerrit Digest

donotreply@...
 

NEW within last 24 hours:
- https://gerrit.zephyrproject.org/r/10553 : samples/net: Add a simple telnet sample
- https://gerrit.zephyrproject.org/r/10563 : samples/net: Fix a tiny mistake in dhcpv4_client README.rst
- https://gerrit.zephyrproject.org/r/10543 : Bluetooth: SPI: switch to a single SPI transfer when receiving
- https://gerrit.zephyrproject.org/r/10564 : Merge net branch into master
- https://gerrit.zephyrproject.org/r/10559 : net: bt: Fix failing to resolve link-local address
- https://gerrit.zephyrproject.org/r/10557 : net: tcp: Call connect callback later
- https://gerrit.zephyrproject.org/r/10544 : Bluetooth: SPI: introduce CONFIG_BLUETOOTH_SPI_BLUENRG
- https://gerrit.zephyrproject.org/r/10524 : samples/zoap_server: Allow overriding the BOARD variable
- https://gerrit.zephyrproject.org/r/10525 : samples/zoap_server: Enable support for 802.15.4
- https://gerrit.zephyrproject.org/r/10551 : Xtensa port: Changed simulation support with xt-run/xtsc-run to be qemu like.
- https://gerrit.zephyrproject.org/r/10531 : net: tcp: Clean up net_context lifecycle
- https://gerrit.zephyrproject.org/r/10532 : net: tcp: Don't send active close FIN packets synchronously
- https://gerrit.zephyrproject.org/r/10547 : Bluetooth: HFP HF: Disconnect rfcomm on SLC error
- https://gerrit.zephyrproject.org/r/10546 : Bluetooth: HFP HF: Indicate disconnect to application
- https://gerrit.zephyrproject.org/r/10545 : kernel: thread: Fix legacy symbol mixup in fp path
- https://gerrit.zephyrproject.org/r/10541 : drivers: dma_shim: update dma qmsi shim driver
- https://gerrit.zephyrproject.org/r/10540 : cov-csv.py: support uploading data to a Google Sheet
- https://gerrit.zephyrproject.org/r/10537 : Xtensa port: Define __builtin_unreachable() as CLI macro when using XCC.
- https://gerrit.zephyrproject.org/r/10536 : Changed Kbuild to pass also KBUILD_CPPFLAGSi to CC on addition to KBUILD_CFLAGS.
- https://gerrit.zephyrproject.org/r/10539 : cov-csv: add verbosity control from command line
- https://gerrit.zephyrproject.org/r/10538 : cov-csv: add argparse support
- https://gerrit.zephyrproject.org/r/10533 : net: tcp: Clean up FIN handling
- https://gerrit.zephyrproject.org/r/10535 : tests: kernel: import errno test to unified
- https://gerrit.zephyrproject.org/r/10529 : tests: context: Verify for out of bounds array
- https://gerrit.zephyrproject.org/r/10526 : cov-csv.py: split maintainer finding to library, port to python3

UPDATED within last 24 hours:
- https://gerrit.zephyrproject.org/r/10257 : samples: grove: use correct i2c device driver name
- https://gerrit.zephyrproject.org/r/9967 : arm: Adjust entry point of XIP kernels to the __reset function
- https://gerrit.zephyrproject.org/r/9856 : drivers: gpio: stm32: Fix build error on stm32f1x/4x for ports F/G/H
- https://gerrit.zephyrproject.org/r/10412 : clock control:stm32: provide STM32Cube LL based driver
- https://gerrit.zephyrproject.org/r/10133 : Windows Build: ussing a precompiled kbuild on windows
- https://gerrit.zephyrproject.org/r/9980 : tests: include: Move timestamp.h into common location
- https://gerrit.zephyrproject.org/r/10413 : gpio: update stm32 gpio to support LL clock control driver
- https://gerrit.zephyrproject.org/r/10424 : boards: nucleo_l476rg: enable support of LL Cube clock control driver
- https://gerrit.zephyrproject.org/r/10423 : board: stm32373c_eval: enable support of LL Cube clock control driver
- https://gerrit.zephyrproject.org/r/10422 : board: nucleo_f334r8: enable support of LL Cube clock control driver
- https://gerrit.zephyrproject.org/r/10421 : soc: stm32f3xx: support of Cube LL Clock driver
- https://gerrit.zephyrproject.org/r/10420 : soc: stm32l4xx: support of Cube LL Clock driver
- https://gerrit.zephyrproject.org/r/10419 : flash: update stm32 flash_f3x to support LL clock control driver
- https://gerrit.zephyrproject.org/r/10418 : pwm: update stm32 pwm to support LL clock control driver
- https://gerrit.zephyrproject.org/r/10417 : i2c: update stm32 i2c_lx to support LL clock control driver
- https://gerrit.zephyrproject.org/r/10416 : i2c: stm32: change deprecated constant
- https://gerrit.zephyrproject.org/r/10487 : fixed Panther board compilation, added support for BLE, moved winc1500 from drivers/ to ext/
- https://gerrit.zephyrproject.org/r/10415 : uart: update stm32 uart to support LL clock control driver
- https://gerrit.zephyrproject.org/r/10414 : pinmux: update stm32 pinmux to support LL clock control driver
- https://gerrit.zephyrproject.org/r/10473 : drivers: stm32: clean up after stm23cube based clock control
- https://gerrit.zephyrproject.org/r/10472 : clock control: clean up after stm32cube LL driver
- https://gerrit.zephyrproject.org/r/10471 : soc: stm32f3x: clean up after Cube LL clock control
- https://gerrit.zephyrproject.org/r/10470 : soc: stm32l4x: clean up after Cube LL clock control
- https://gerrit.zephyrproject.org/r/10239 : added preliminary version of winc1500 driver and Arrow Panther support
- https://gerrit.zephyrproject.org/r/10333 : test_mbedtls: for testing Port AES-CMAC-PRF-128 library
- https://gerrit.zephyrproject.org/r/9717 : Bluetooth: shell: Add support to retrieve A2SRC record
- https://gerrit.zephyrproject.org/r/9713 : Bluetooth: SDP: Add API to get ProfileDescriptorList attribute
- https://gerrit.zephyrproject.org/r/9716 : Bluetooth: shell: Use SupportedFeature attribute API
- https://gerrit.zephyrproject.org/r/9714 : Bluetooth: shell: Add getting ProfileDescriptorList attribute
- https://gerrit.zephyrproject.org/r/9715 : Bluetooth: SDP: Add API to get SupportedFeature attribute
- https://gerrit.zephyrproject.org/r/9711 : Bluetooth: SDP: Get ProtocolDescriptorList attribute internals
- https://gerrit.zephyrproject.org/r/9712 : Bluetooth: shell: Add SDP client support
- https://gerrit.zephyrproject.org/r/9460 : Bluetooth: AVDTP: Add AVDTP Discover Function Definition
- https://gerrit.zephyrproject.org/r/10516 : sensor: add SENSOR_CHAN_*_XYZ enum values
- https://gerrit.zephyrproject.org/r/10507 : sensor: use SENSOR_CHAN_*_XYZ instead of SENSOR_CHAN_*_ANY
- https://gerrit.zephyrproject.org/r/10183 : irq: introduce 'direct' interrupt API definition
- https://gerrit.zephyrproject.org/r/10475 : Simple PWM driver for nRF5
- https://gerrit.zephyrproject.org/r/9517 : samples: net: echo_server .conf for Atmel SMART SAM E70 Xplained board
- https://gerrit.zephyrproject.org/r/10476 : board: add nucleo_411re board documentation
- https://gerrit.zephyrproject.org/r/10505 : doc: update template for nucleo_f401re board
- https://gerrit.zephyrproject.org/r/10479 : Bluetooth: HFP HF: Service level connection completed
- https://gerrit.zephyrproject.org/r/10426 : Bluetooth: HFP HF: Enable extended AG Error Result Code
- https://gerrit.zephyrproject.org/r/7492 : Bluetooth: A2DP: Added Preset Structure
- https://gerrit.zephyrproject.org/r/6720 : Bluetooth: A2DP: Stream End Point Registration
- https://gerrit.zephyrproject.org/r/10512 : doc: update copyright for documentation
- https://gerrit.zephyrproject.org/r/10456 : ext: lib: mbedtls : mbedTLS library modifications
- https://gerrit.zephyrproject.org/r/10489 : api: dma: dma api update
- https://gerrit.zephyrproject.org/r/10076 : verify: replace verify build steps with run_phases call
- https://gerrit.zephyrproject.org/r/10454 : archives: refactor archive script
- https://gerrit.zephyrproject.org/r/9854 : http: add server sample
- https://gerrit.zephyrproject.org/r/4457 : DONT: MERGE - cause checkpatch warnings
- https://gerrit.zephyrproject.org/r/10117 : doc: move context back to doc/, fix broken links
- https://gerrit.zephyrproject.org/r/9762 : CI: rearchitect with a framework that orchestrates running
- https://gerrit.zephyrproject.org/r/10323 : Xtensa port: Added linker script for several Xtensa cores.
- https://gerrit.zephyrproject.org/r/10515 : Xtensa port: Added support for Xtensa internal timer as system timer.
- https://gerrit.zephyrproject.org/r/9678 : http: add server sample
- https://gerrit.zephyrproject.org/r/5475 : DONT MERGE - break sanity AND checkpatch
- https://gerrit.zephyrproject.org/r/10187 : test
- https://gerrit.zephyrproject.org/r/5895 : DONT MERGE - test CI time with only 1 level
- https://gerrit.zephyrproject.org/r/9977 : samples: net: "Mini HTTP" example & validator for TCP layer
- https://gerrit.zephyrproject.org/r/10478 : TEST: DONT MERGE https://gerrit.zephyrproject.org/r/#/c/10359/1 The above line should trigger a warning or an error.
- https://gerrit.zephyrproject.org/r/10075 : net/mqtt: Add the MQTT Publisher sample application
- https://gerrit.zephyrproject.org/r/9681 : quark_se: Add shared GDT in RAM memory to linker
- https://gerrit.zephyrproject.org/r/9682 : quark_d2000: Add shared GDT memory to linker
- https://gerrit.zephyrproject.org/r/9680 : quark_se: Fix restore info address
- https://gerrit.zephyrproject.org/r/8803 : benchmarks: boot_time: Move to unified kernel
- https://gerrit.zephyrproject.org/r/10506 : tests: kernel: mem_heap: added api and concept tests
- https://gerrit.zephyrproject.org/r/10477 : RFC: bluetooth: hci: Add VS header and new command to retrieve random addrs

MERGED within last 24 hours:
- https://gerrit.zephyrproject.org/r/10562 : ext: hal: nordic: cleanup Kbuild for now
- https://gerrit.zephyrproject.org/r/10555 : ext: Import Nordic SDK HAL files
- https://gerrit.zephyrproject.org/r/10556 : ext: Integrate Nordic SDK HAL files into Zephyr
- https://gerrit.zephyrproject.org/r/10561 : Bluetooth: samples: Use Kconfig DEVICE_NAME variable when possible
- https://gerrit.zephyrproject.org/r/10560 : Bluetooth: Kconfig: Make device name variable generic
- https://gerrit.zephyrproject.org/r/10558 : MAINTAINERS: Remove Jon Medhurst from MPS2 maintainership
- https://gerrit.zephyrproject.org/r/10517 : drivers/console/telnet: Select TCP when telnet is selected
- https://gerrit.zephyrproject.org/r/10542 : Bluetooth: SPI: fix buf handling for HCI ACL packets
- https://gerrit.zephyrproject.org/r/10554 : net: Fix leaving NET_MAX_6LO_CONTEXTS set when 6lowpan deselected
- https://gerrit.zephyrproject.org/r/10552 : net/shell: Fix format string
- https://gerrit.zephyrproject.org/r/10549 : net: tests: Correct project file for route tests
- https://gerrit.zephyrproject.org/r/10550 : net: Remove unused CONFIG_NET_IPV6_NO_DAD option
- https://gerrit.zephyrproject.org/r/10519 : net/6lo: Switch to NET_ERR/NET_WARN when relevant.
- https://gerrit.zephyrproject.org/r/10518 : net/ieee802154: Raise an error when data frame cannot be created
- https://gerrit.zephyrproject.org/r/10520 : doc: Update mps2_an385 documentation
- https://gerrit.zephyrproject.org/r/10534 : doc: fix wiki board reference back to web page
- https://gerrit.zephyrproject.org/r/10523 : Xtensa port: Enable long calls for Xtensa vector table.
- https://gerrit.zephyrproject.org/r/10521 : doc: update bluetooth samples with pointers
- https://gerrit.zephyrproject.org/r/10530 : license: fix SPDX headings on new tests
- https://gerrit.zephyrproject.org/r/10527 : doc: fix broken link to board doc
- https://gerrit.zephyrproject.org/r/10528 : doc: fix incorrect ReST heading hierarchy
- https://gerrit.zephyrproject.org/r/10522 : Xtensa port: Fixed tests/kernel/context to compile with Xtensa internal timer.
- https://gerrit.zephyrproject.org/r/10511 : net: echo-client: Add TCP support
- https://gerrit.zephyrproject.org/r/10430 : ext: stm32cube: update stm32l4xx cube version
- https://gerrit.zephyrproject.org/r/10429 : ext: stm32cube: update stm32f4xx cube version
- https://gerrit.zephyrproject.org/r/10319 : Xtensa port: Added Xtensa specific code (C + S) files.
- https://gerrit.zephyrproject.org/r/10513 : net: Make NET_IPV6_ND configurable option
- https://gerrit.zephyrproject.org/r/10514 : net: Make NET_IPV6_DAD depends on NET_IPV6_ND
- https://gerrit.zephyrproject.org/r/10504 : net: 6lo: Fix tiny style issues
- https://gerrit.zephyrproject.org/r/10503 : net: dhcpv4: Fix tiny style issues
- https://gerrit.zephyrproject.org/r/10510 : net/ieee802154: Modify radio TX function signature
- https://gerrit.zephyrproject.org/r/10486 : boards: arm: mps2: Add pinmuxing
- https://gerrit.zephyrproject.org/r/10488 : frdm_k64f: Add RST board documentation
- https://gerrit.zephyrproject.org/r/10455 : Revert "sanitycheck: add support for risc v boards"
- https://gerrit.zephyrproject.org/r/9609 : sanity: prevent stack corruption at test_static_idt
- https://gerrit.zephyrproject.org/r/9504 : sanity: prevent stack corruption at test_sema
- https://gerrit.zephyrproject.org/r/9642 : maintainers: update KNOWN ISSUES and MAINTAINERS section
- https://gerrit.zephyrproject.org/r/9049 : sanity: filter the build-all test for ethernet
- https://gerrit.zephyrproject.org/r/10320 : Xtensa port: Moved XCC specific libraries out of genric Xtensa make file.
- https://gerrit.zephyrproject.org/r/10261 : Disable automatic system updates on Ubuntu
- https://gerrit.zephyrproject.org/r/10495 : doc: fix links in zephyr theme template footer


Re: File system

Thomas, Ramesh
 

On Thu, Jan 26, 2017 at 09:08:37, Fábio Iaione wrote:
Dear Sirs,
I am trying to use the FAT file system in Galileo Gen1 and I have the
following doubts:
1- Does it work on Galileo Gen1?
The file system will work provided a disk access layer and flash driver is
implemented for it. Currently these are only implemented for Winbond
flash on the Arduino 101 boards. (susbs/disk/disk_access_flash.c and
drivers/spi_flash_w25qxxdv.c)

Refer to the following header files for the disk_access and flash interfaces
if you would be interested in implementing them.
include/disk_access.h
include/flash.h

2- The file system will be created in SPI flash or SD card?
The current implementation uses Winbond SPI flash on Arduino 101.


File system

Fábio Iaione <fabio.iaione at gmail.com...>
 

Dear Sirs,

I am trying to use the FAT file system in Galileo Gen1 and I have the following doubts:

1- Does it work on Galileo Gen1?

2- The file system will be created in SPI flash or SD card?

Thank you.


File system

Fábio Iaione <fabio.iaione at gmail.com...>
 

Dear Sirs,
I am trying to use the FAT file system in Galileo Gen1 and I have the following doubts:
1- Does it work on Galileo Gen1?
2- The file system will be created in SPI flash or SD card?
Thank you.


Daily Gerrit Digest

donotreply@...
 

NEW within last 24 hours:
- https://gerrit.zephyrproject.org/r/10513 : net: Make NET_IPV6_ND configurable option
- https://gerrit.zephyrproject.org/r/10510 : net/ieee802154: Modify radio TX function signature
- https://gerrit.zephyrproject.org/r/10486 : boards: arm: mps2: Add pinmuxing
- https://gerrit.zephyrproject.org/r/10515 : Xtensa port: Added support for Xtensa internal timer as system timer.
- https://gerrit.zephyrproject.org/r/10507 : sensor: use SENSOR_CHAN_*_XYZ instead of SENSOR_CHAN_*_ANY
- https://gerrit.zephyrproject.org/r/10516 : sensor: add SENSOR_CHAN_*_XYZ enum values
- https://gerrit.zephyrproject.org/r/10512 : doc: update copyright for documentation
- https://gerrit.zephyrproject.org/r/10514 : net: Make NET_IPV6_DAD depends on NET_IPV6_ND
- https://gerrit.zephyrproject.org/r/10503 : net: dhcpv4: Fix tiny style issues
- https://gerrit.zephyrproject.org/r/10511 : net: echo-client: Add TCP support
- https://gerrit.zephyrproject.org/r/10504 : net: 6lo: Fix tiny style issues
- https://gerrit.zephyrproject.org/r/10509 : i2c/nrf5: Remove r/w to POWER register.
- https://gerrit.zephyrproject.org/r/10505 : doc: update template for nucleo_f401re board
- https://gerrit.zephyrproject.org/r/10506 : tests: kernel: mem_heap: added api and concept tests
- https://gerrit.zephyrproject.org/r/10500 : tests: kernel: port mutex/priority inheritance test to unified
- https://gerrit.zephyrproject.org/r/10488 : frdm_k64f: Add RST board documentation
- https://gerrit.zephyrproject.org/r/10495 : doc: fix broken links in zephyr theme template footer
- https://gerrit.zephyrproject.org/r/10491 : tests: kernel: import pool/heap tests to unified
- https://gerrit.zephyrproject.org/r/10489 : api: dma: dma api update
- https://gerrit.zephyrproject.org/r/10487 : fixed Panther board compilation, added support for BLE, moved winc1500 from drivers/ to ext/
- https://gerrit.zephyrproject.org/r/10484 : arm: cmsis: Convert _ScbIsInThreadMode to use direct CMSIS register access
- https://gerrit.zephyrproject.org/r/10483 : arm: cmsis: Convert _ScbPendsvSet to use direct CMSIS register access
- https://gerrit.zephyrproject.org/r/10485 : arm: scb: Move SCB asm defines into cpu_idle.S
- https://gerrit.zephyrproject.org/r/10481 : arm: refactor clearing of exception faults to common code
- https://gerrit.zephyrproject.org/r/10482 : arm: cmsis: Convert _ScbNmiPend to use direct CMSIS register access
- https://gerrit.zephyrproject.org/r/10478 : TEST: DONT MERGE https://gerrit.zephyrproject.org/r/#/c/10359/1 The above line should trigger a warning or an error.
- https://gerrit.zephyrproject.org/r/10479 : Bluetooth: HFP HF: Service level connection completed

UPDATED within last 24 hours:
- https://gerrit.zephyrproject.org/r/10456 : ext: lib: mbedtls : mbedTLS library modifications
- https://gerrit.zephyrproject.org/r/10075 : net/mqtt: Add the MQTT Publisher sample application
- https://gerrit.zephyrproject.org/r/4872 : DO NOT MERGE: k_poll: asynchronous I/O framework
- https://gerrit.zephyrproject.org/r/10323 : Xtensa port: Added linker script for several Xtensa cores.
- https://gerrit.zephyrproject.org/r/10477 : RFC: bluetooth: hci: Add VS header and new command to retrieve random addrs
- https://gerrit.zephyrproject.org/r/10320 : Xtensa port: Moved XCC specific libraries out of genric Xtensa make file.
- https://gerrit.zephyrproject.org/r/10319 : Xtensa port: Added Xtensa specific code (C + S) files.
- https://gerrit.zephyrproject.org/r/10183 : irq: introduce 'direct' interrupt API definition
- https://gerrit.zephyrproject.org/r/10476 : board: add nucleo_411re board documentation
- https://gerrit.zephyrproject.org/r/10093 : samples/net/http: Add the server sample application
- https://gerrit.zephyrproject.org/r/9517 : samples: net: echo_server .conf for Atmel SMART SAM E70 Xplained board
- https://gerrit.zephyrproject.org/r/8949 : samples: zperf: Correct the include files path to eliminate compile errors
- https://gerrit.zephyrproject.org/r/10369 : ataes132a: Adds a driver to support ATAES132A device
- https://gerrit.zephyrproject.org/r/3311 : include/crypto: Crypto abstraction header
- https://gerrit.zephyrproject.org/r/9883 : i2c: Adds a functions set that supports 16 bit addressing.
- https://gerrit.zephyrproject.org/r/10178 : samples/net/http: Introduce routines to handle multiple contexts
- https://gerrit.zephyrproject.org/r/10258 : samples/net/http: Add support for multiple URLs
- https://gerrit.zephyrproject.org/r/9854 : http: add server sample
- https://gerrit.zephyrproject.org/r/10436 : net: correct/clarify in*_addr parameter of net_addr_pton()
- https://gerrit.zephyrproject.org/r/10257 : samples: grove: use correct i2c device driver name
- https://gerrit.zephyrproject.org/r/9682 : quark_d2000: Add shared GDT memory to linker
- https://gerrit.zephyrproject.org/r/9681 : quark_se: Add shared GDT in RAM memory to linker
- https://gerrit.zephyrproject.org/r/9680 : quark_se: Fix restore info address
- https://gerrit.zephyrproject.org/r/10475 : Simple PWM driver for nRF5
- https://gerrit.zephyrproject.org/r/10424 : boards: nucleo_l476rg: enable support of LL Cube clock control driver
- https://gerrit.zephyrproject.org/r/10420 : soc: stm32l4xx: support of Cube LL Clock driver
- https://gerrit.zephyrproject.org/r/10422 : board: nucleo_f334r8: enable support of LL Cube clock control driver
- https://gerrit.zephyrproject.org/r/10418 : pwm: update stm32 pwm to support LL clock control driver
- https://gerrit.zephyrproject.org/r/10412 : clock control:stm32: provide STM32Cube LL based driver
- https://gerrit.zephyrproject.org/r/10423 : board: stm32373c_eval: enable support of LL Cube clock control driver
- https://gerrit.zephyrproject.org/r/10471 : soc: stm32f3x: clean up after Cube LL clock control
- https://gerrit.zephyrproject.org/r/10415 : uart: update stm32 uart to support LL clock control driver
- https://gerrit.zephyrproject.org/r/10419 : flash: update stm32 flash_f3x to support LL clock control driver
- https://gerrit.zephyrproject.org/r/10414 : pinmux: update stm32 pinmux to support LL clock control driver
- https://gerrit.zephyrproject.org/r/10417 : i2c: update stm32 i2c_lx to support LL clock control driver
- https://gerrit.zephyrproject.org/r/10473 : drivers: stm32: clean up after stm23cube based clock control
- https://gerrit.zephyrproject.org/r/10470 : soc: stm32l4x: clean up after Cube LL clock control
- https://gerrit.zephyrproject.org/r/10421 : soc: stm32f3xx: support of Cube LL Clock driver
- https://gerrit.zephyrproject.org/r/10472 : clock control: clean up after stm32cube LL driver
- https://gerrit.zephyrproject.org/r/10416 : i2c: stm32: change deprecated constant
- https://gerrit.zephyrproject.org/r/10413 : gpio: update stm32 gpio to support LL clock control driver
- https://gerrit.zephyrproject.org/r/10426 : Bluetooth: HFP HF: Enable extended AG Error Result Code

MERGED within last 24 hours:
- https://gerrit.zephyrproject.org/r/10480 : soc: arm: mps2: Fix UART4 base address
- https://gerrit.zephyrproject.org/r/10508 : net: Remove CONFIG_NET_IPV6_NO_ND config option
- https://gerrit.zephyrproject.org/r/10502 : tunslip6: strengthen and defer config to external parties
- https://gerrit.zephyrproject.org/r/10499 : samples: fxos8700: Convert documentation to RST
- https://gerrit.zephyrproject.org/r/10498 : samples: fxos8700: Decimate sensor data before printing to the console
- https://gerrit.zephyrproject.org/r/10497 : fxos8700: Fix broken gpio callback implementation
- https://gerrit.zephyrproject.org/r/10496 : MAINTAINERS: add Andrew to x86
- https://gerrit.zephyrproject.org/r/10493 : Xtensa port: Added support for Xtensa architecture to linker-defs.h.
- https://gerrit.zephyrproject.org/r/10494 : MAINTAINERS: add xtensa arch
- https://gerrit.zephyrproject.org/r/10375 : samples/coaps_client CoAP over DTLS client example app using mbedTLS
- https://gerrit.zephyrproject.org/r/10249 : samples/coaps_server CoAP over DTLS server example app using mbedTLS
- https://gerrit.zephyrproject.org/r/10443 : shell: Fix tiny style issues
- https://gerrit.zephyrproject.org/r/10447 : shell: Make the command queue size configurable via Kconfig
- https://gerrit.zephyrproject.org/r/10438 : drivers/console: Removing non existing Kconfig source
- https://gerrit.zephyrproject.org/r/10440 : net: ip: Add a useful macro to staticaly initialize a struct in_addr
- https://gerrit.zephyrproject.org/r/10445 : drivers/console: Making console input generic
- https://gerrit.zephyrproject.org/r/10449 : shell: If enabled, let's register telnet console as an input
- https://gerrit.zephyrproject.org/r/10444 : drivers/uart_console: Fix tiny style issues
- https://gerrit.zephyrproject.org/r/10446 : console/shell: Switch to generic console input
- https://gerrit.zephyrproject.org/r/10442 : samples/net: Add telnet console support on echo_server with qemu
- https://gerrit.zephyrproject.org/r/10450 : drivers/console/telnet: Add ground support for telnet commands
- https://gerrit.zephyrproject.org/r/10441 : drivers/console: Add a basic telnet console
- https://gerrit.zephyrproject.org/r/10439 : misc/printk: Add a function to get the current hook function.
- https://gerrit.zephyrproject.org/r/10448 : drivers/console/telnet: Provide minimal input handling.
- https://gerrit.zephyrproject.org/r/10435 : Xtensa port: Added support for Xtensa simulator console driver.
- https://gerrit.zephyrproject.org/r/10465 : Xtensa port: Added Xtensa internal timer configuration need by assembly files.
- https://gerrit.zephyrproject.org/r/10324 : Xtensa port: Removed the need to put an empy file soc.c in arch/xtensa/soc dir.
- https://gerrit.zephyrproject.org/r/10453 : xtensa: fix find_msb_set() and find_lsb_set()
- https://gerrit.zephyrproject.org/r/10452 : xtensa: fixup license identifiers
- https://gerrit.zephyrproject.org/r/10469 : pinmux: make pinmux_dev the default pinmux driver for quark
- https://gerrit.zephyrproject.org/r/10474 : pinmux: unify galileo pinmux driver
- https://gerrit.zephyrproject.org/r/10318 : Xtensa port: Added support for Xtensa architecture in zephyr include files.
- https://gerrit.zephyrproject.org/r/6719 : Bluetooth: A2DP: Stream End Point Structure
- https://gerrit.zephyrproject.org/r/10432 : arm: move exception priority to exc.h
- https://gerrit.zephyrproject.org/r/10170 : arm: cmsis: Convert _ScbExcPrioSet to NVIC_SetPriority
- https://gerrit.zephyrproject.org/r/10171 : arm: cmsis: Remove nvic.h and use CMSIS NVIC calls directly
- https://gerrit.zephyrproject.org/r/10359 : commit-message: skip length checks for http/https URLs


Re: I2C compatibility with nrf52

Nicolas Perrenoud <nicolas.perrenoud@...>
 

Hi, Short term, just remove the two lines in question. I'll talk to
Carlesc and the Nordic guys to figure out what the proper solution
should be.
Ok Thanks

Nicolas


Re: I2C compatibility with nrf52

Marcus Shawcroft <marcus.shawcroft@...>
 

On 26 January 2017 at 08:56, Nicolas Perrenoud
<nicolas.perrenoud(a)geo-satis.com> wrote:

Is there some thinks special to do to compile for NRF52 or is it ok to just
comment these two lines ?
Hi, Short term, just remove the two lines in question. I'll talk to
Carlesc and the Nordic guys to figure out what the proper solution
should be.

Cheers
/Marcus

5661 - 5680 of 8046