devel@lists.zephyrproject.org

Re: Sleep current on #nrf52480

Hi You could also try following patch which is currently under review: https://github.com/zephyrproject-rtos/zephyr/pull/7034#issuecomment-401265397 Regards, Ismael

By ismael fillonneau · #4820 ·

Re: SODAQ One V3 porting

Back again! So this is weird because I got it working but without TX interrupts. RX interrupts work fine however as soon as I enable TX interrupts with uart_irq_tx_enable I enter an interruption

By Léonard Bise <leodido99@...> · #4819 ·

Re: Sleep current on #nrf52480

550uA usually means that the HFCLK is running. The HFCLK will run when something (peripheral) needs it. You need to find out what is using it, unfortunately neither the HW or the SW is able to tell

By Sebastian Boe · #4818 ·

Sleep current on #nrf52480

Hi all, I've ran some power consumption tests with Zephyr 1.12 #... a00646a5 Using the samples/boards/nrf52/pwr_mgr at lowest power mode, I find that the nrf52840 has a sleep current of ~550uA. When I

By Fabien Lepoutre · #4817 ·

Re: SODAQ One V3 porting

I'm having difficulties trying to communicate with the LoRa UART interface. I set it up like so: pinmux.c #if CONFIG_UART_SAM0_SERCOM2_BASE_ADDRESS /* SERCOM2 LoRa UART on RX=PA13/pad 1, TX=PA12/pad

By Léonard Bise <leodido99@...> · #4816 ·

[Zephyr-users] OpenThread example from embedded world conf #nrf52840

---------- Forwarded message ---------- From: Lubos, Robert <Robert.Lubos@...> Date: Thu, Jun 28, 2018 at 1:14 PM Subject: RE: [Zephyr-users] OpenThread example from embedded world conf #nrf52840 To:

By vikrant8051 <vikrant8051@...> · #4815 ·

Re: Mbedtls_pk_verify error

There are still buffer/variable overflow problems, so I would make sure those are fixed before trying to figure out why else it might not be working. For example: char buffer[2]; ...

By David Brown · #4814 ·

Re: SODAQ One V3 porting

I'm back again! I think I sent the last mail only to Brix by mistake. I'm happy to say that I fixed my issue... I needed to set my pin mux function as D not C. #if

By Léonard Bise <leodido99@...> · #4813 ·

Re: zephyr question

Hi there, I just tried this but instead of using menuconfig I changed my prj.conf like this: diff --git a/samples/bluetooth/peripheral_hr/prj.conf

By Carles Cufi · #4812 ·

Re: advertising data

Hi Tamra, The format of the data (behind ad->data with length ad->len) is specified in the Bluetooth Core Specification (5.0) Volume 3, Part C, section 11 (page 2086 in the pdf). In practice it's

By Johan Hedberg · #4811 ·

Re: advertising data

You might also want to try Nordic’s “nRF Connect” on Android. It could show you all the details of hex received in advertising and scan response packet, in raw and parsed mode. BR, zou

By Zou, Jun Qing · #4810 ·

Re: advertising data

Hi all, Thanks for the help. From what I can tell "ad" from "struct net_buf_simple *ad" is the payload, and so I'm wondering what format is the payload in. (i.e if i convert it to binary where in the

By Tamra <tamrako@...> · #4809 ·

zephyr question

Hi Sir, We occurred some question when we use zephyr in nRF52832. We found there were some chips cannot boot-up w/ Zephyr sample code (disable UART), but can boot up well w/ Nordic original

By Hsu, Hanyu <Hanyu.Hsu@...> · #4808 ·

Release readiness meeting cancelled

Hi all, We have had to cancel the Release Readiness meeting today due to technical issues with the conferencing system. Apologies for the late notice. Regards, Carles

By Carles Cufi · #4807 ·

Re: advertising data

Hi, I'd like to add here that we've just merged a new helper API for parsing the advertising data: https://github.com/zephyrproject-rtos/zephyr/pull/8560 This pull request also included updating

By Johan Hedberg · #4806 ·

Re: ticker timer #nrf52840 #ble #nrf52832

Hi there, I copied Vinayak who is the original author of the ticker. There is no real material available publicly at this point. Regards, Carles

By Carles Cufi · #4805 ·

ticker timer #nrf52840 #ble #nrf52832

Hello, I am trying to understand ticker timer. and have confusion between user id's, what is the difference between RADIO_TICKER_USER_ID_WORKER and RADIO_TICKER_USER_ID_APP? is there any material

By swapnil <swapnil2007kadam@...> · #4804 ·

Re: advertising data

Hi Tamra, <luiz.dentz@...> wrote: Actually the event type is no the AD type, sorry about that, so 0x03 refers to BT_LE_ADV_NONCONN_IND. -- Luiz Augusto von Dentz

By Luiz Augusto von Dentz · #4803 ·

Re: advertising data

Hi Tamra, The type you will be able to find in the assigned number for GAP: https://www.bluetooth.com/specifications/assigned-numbers/generic-access-profile AD payload format for each type is

By Luiz Augusto von Dentz · #4802 ·

advertising data

Hi all, I'm looking at the central_hr example. I was wondering what information is packed into the net_buf_simple *ad? The function and output is below. static void device_found(const bt_addr_le_t

By Tamra <tamrako@...> · #4801 ·

Messages