This is an excellent idea. The only downside (upside?) is having to standardize on all of the subsystem driver labels. And it still doesn't solve the device specific properties unless we were to

Hi, I wanna send some chuck of data over USART to #nRF52840_PDK like commands. Is there any sample code available for it or any configuration is required to enable this USART read feature ? Thank You

Hi, Sorry for the delay in replying (working on another project). I can confirm the problem still occurs with Controller Privacy turned off, as you suggested would be the case. It

Hello Oleg, I'm writing to you about your project to develop a testsuite for Zephyr networking stack using TTCN-3 test language, https://github.com/intel/net-test-suites . I also cc: this to

Hi Chuck, On top of CONFIG_SPI you have to specify which SPI interface your are using, that it is a NRFX SPI and the associated pins in your prj.conf. Here is an example for the nrf52840_pca10056 I

Hello Anas, "Nashif, Anas" <anas.nashif@...> wrote: Thanks for the prompt pre-release process notifications to the mailing list this cycle. Hope it'll become a good tradition ;-). Any

Hi, We have tagged Zephyr 1.13 rc1 and with that closed the merge window for 1.13. Focus now will go into bug fixing, testing and documentation. All new features will be merged after 1.13 is

Hi Chuck, All that I am sayings is, do not modify your repository, do not add anything to prj,conf file. execute cmake, then either use make or ninja for the target config or menuconfig. Then you get

Vinayak, Thanks for being persistent in looking at this issue. Sorry for some confusion, I probably didn't state the behavior I'm seeing very clearly. At this point, the issue is that the cmake does

Hi Chuck, I do not understand “menuconfig will not run on the project”, you may want to check your toolchain requirements and/or make a clean build, check that cmake command for the board and

Justin, Vinayak, Thanks, still digging into this. So far, the cmake phase is not properly copying the drivers into the library and failing before any make files are produced. So, menuconfig will not

Hi Johan, It is nothing to do with controller privacy, its just that advertiser is active and by BT Spec. “If the Host issues this command when scanning or legacy advertising is enabled, the

Folks, I was thinking about doing a code cleanup in the dts.fixup and uart and gpio driver for the i.MX7 SoC, where we create redundant defines already covered by devicetree aliases. Here is a breif

I believe that the SPI driver for NRF52 doesn't support DTS yet, and you have to configure it through the config files. I'm not sure why that's the case and if something is preventing it from being

Hi, Could you please turn off the controller privacy feature and check if you still face issues? CONFIG_BT_CTLR_PRIVACY=n This is to narrow down the locality of the problem, just suspecting some

Hi Johan, I have attached a new log. This time it fails after 121 cycles (maybe the 128 was a coincidence and the extra debug has changed the timing?). Any ideas what is

Thanks Declan. The logs do indeed show the HCI error: [bt] [DBG] bt_hci_cmd_send_sync: (0x20004240) opcode 0x2005 status 0x0c 0x0c is the same as "Command Disallowed", i.e. the controller

hi guys, I got a problem here and hope anyone can give me some advice,thanks. I bought a official nrf52832 development kits and ported zephyr project successfully. It runs fine with my ubuntu

Thanks David. However since I had this issue, I change the board definition to have a board out of zephyr scope, since it is a board created here in the compagny for a specific custom. Before I used

How could I create image that will be signed that mcuboot will recognise it as valid image. I wuild like to sign image with imgtool.py in ninja script after build (target all) was succesfull. Thanks