Hi I am trying to publish some data using a vendor model, and I am getting error code -125 ( -EADDRNOTAVAIL). Knowing the device was successfully configured and the key was bound correctly with no

Hi I have implemented a mesh network code based on the mesh sample (samples\bluetooth\mesh), I have added two vendor models and it works great when I tested it. Now I'm trying to make these vendor

Reminder: Zephyr Project: Dev Meeting When: 09/02/2021 3:00pm to 4:00pm (UTC+00:00) UTC Where: Microsoft Teams Meeting Organizer: devel@... An RSVP is requested. Click here to

posix_apis: fails at test_posix_realtime for mimxrt1024_evk - https://github.com/zephyrproject-rtos/zephyr/issues/35703 drivers: regulator: convert to gpio_dt_spec -

Hi there, the KConfig files contain the definitions of possible configuration options. You can then set them in your prj.conf like this: CONFIG_BT_CTLR_TX_PWR_PLUS_5=y

Hi, I have a technical question, I'm trying to modify the Tx power of the hci_usb sample before flashing it to a controller. I've found in the zephyr/subsys/bluetooth/controller/Kconfig file that I

Reminder: Zephyr Project: APIs When: 08/31/2021 4:00pm to 5:00pm (UTC+00:00) UTC Where: Microsoft Teams Meeting Organizer: devel@... An RSVP is requested. Click here to

Hi all, Agenda for today: - RFC: API change: Add SMbus support to I2C API - Issue: https://github.com/zephyrproject-rtos/zephyr/issues/37101 - Pinctrl: Side-by-side comparison of two (similar)

Reminder: Zephyr Memory Footprint - biweekly discussion When: 08/30/2021 3:00pm to 4:00pm (UTC+00:00) UTC Where: Microsoft Teams Meeting Organizer: devel@... An RSVP is requested. Click

Hi, To support low power mode, you must set CONFIG_BT_MESH_LOW_POWER=y. To make the device enter low power mode, either set CONFIG_BT_MESH_LPN_AUTO=y or call bt_mesh_lpn_set(true). Note that low

Hi all, I'm trying to set up the LWM2M client sample with the ot overlay on a nrf52840 platform. So far, I have set up the OTBR and I am able to ping the outside world (net ping 64:ff9b::8.8.8.8 is

Hi I am testing the bluetooth mesh sample (samples\bluetooth\mesh) on a battery-powered device, I have to activate the low power mode in order to make it consume the least amount of power. What's

Sorry for the late cancellation. I’m on vacation this week. - k

Cancelled: Zephyr Project: Dev Meeting This event has been cancelled. When: Thursday, August 26, 2021 3:00pm to 4:00pm (UTC+00:00) UTC Where: Microsoft Teams Meeting Organizer:

Reminder: Zephyr Project: Dev Meeting When: 08/26/2021 3:00pm to 4:00pm (UTC+00:00) UTC Where: Microsoft Teams Meeting Organizer: devel@... An RSVP is requested. Click here to

Hi, Both buffer errors are a result of missing adv buffers. To minimize copying, both relay buffers and transport buffers are allocated from the advertising buffer pool, so that's the one that needs

Hi Vinayak, Thank you so much for the information. Regards, Nandhakumar

Reminder: Zephyr Project: APIs When: 08/24/2021 4:00pm to 5:00pm (UTC+00:00) UTC Where: Microsoft Teams Meeting Organizer: devel@... An RSVP is requested. Click here to

Sorry, got it by myself. You have to select the code partition in the device tree: chosen { zephyr,code-partition = &slot0_partition; }; Thanks anyway! Benedikt

Hi there, I have got a problem with the MCU bootloader. To get it up and running I am following the steps documented in https://docs.zephyrproject.org/latest/guides/west/sign.html. With some slight