Hi Community, I have one custom board on which I'm having Nordic's nrf52840_pca10056 chip on which i have flashed zephyr's 'hci_uart' sample application for the beacon scanning purpose. "hci_uart" app

#ble #hci #nrf52480 #uart

Hello All, I have one question regarding the ability of zephyr's hci_uart sample app. I am using this application on nrf52840_pca10056 for scanning the ble beacons. Scenario is i can see "hci0" interf

#uart #ninja #ble #hci #nrf52480

Hi All, I have observed one thing related to zephyr's hci_uart sample application. I have used above application to implement the logic of beacon scanning in my custom application. (Used Bluez 5.50 fr

#ble #hci #nrf52480 #samples #uart

Hi Vinayak, Thank you for the support. I have created the GH issue for the same https://github.com/zephyrproject-rtos/zephyr/issues/23319 Thanks, Mayank

#ble #hci #nrf52480 #uart

Hi All, Here i'm facing the issue even after using the full UART (Tx, Rx, RTS, CTS). These 4 pins are connected & configured from both (i.MX6UL & nrf52840_pca10056). Note : nrf52840 chip is flashed wi

#ble #hci #nrf52480 #uart

So does anyone have idea regarding this issue ? I'm using zephyr (Version : 2.1.0) and Bluez (Version : 5.50). Thanks, Mayank

#ble #hci #nrf52480 #uart

Hi All, I'm facing issues regarding ble's hci interface. I'm having nrf52840 module on which i run zephyr's hci_uart app for beacon scanning. I have Bluez 5.50 installed on my custom board (imx6ull).

#ble #hci #nrf52480 #uart

Hi Johan, Should i go with the Hardware flow control as enable to solve the buffer flow issue ? Not using HWFC could have any other adverse effect? As my current implementation is based on flow contro

#uart #samples #ble #hci #nrf52480

Hi All, I have a doubt regarding one of the sample application of zephyr (samples/bluetooth/hci_uart). This 'hci_uart' application has Hardware flow control enable by default in its nrf.conf file. (CO

#uart #samples #ble #hci #nrf52480

Hello, I have nrf52840_pca10056 chip connected to imx6ul processor via uart (Both are embedded on my custom board) as shown in attached image. I'm using mcuboot bootloader on nrf52840 chip, now i want

#ble #hci #nrf52480 #uart

Hello All, Right now I'm exploring the best way to do DFU OTA. I would like to ask that how i can do the DFU by booting the mcuboot bootloader in serial recovery mode. I have one nrf52840_pca10056 chi

#ble #hci #nrf52480 #uart

Hi, I want to do an DFU OTA in nRF52840 BLE chip. I have flashed mcuboot bootloader and also flashed hci_uart (To scan BLE beacons) application. This will be one time flash using JTAG. Now, I want to

#hci #nrf52480 #ble #uart #samples

Thanks Adam, I have upgraded zephyr to latest version (2.1.0) using west update. Now with the configuration of my application as well as mcuboot, i reached at the stage where i can upload the signed a

#ble #bluetoothmesh #nrf52840 #uart

Thanks Adam, I have disabled BT and Shell, Only UART is there. Now, when i run the command with debug mode --> mcumgr -ldebug --conntype=serial --connstring='dev=/dev/ttymxc0,baud=115200' echo hello I

#ble #bluetoothmesh #nrf52840 #uart

Thanks Jamie, Here, I would like to point out the exact setup that i'm trying DFU on. I have One custom board which has imx6ul processor, I'm having one BLE controller on board which is connected to p

#nrf52840 #ble #bluetoothmesh

Hi, I'm trying to do an OTA of zephyr hci_uart application and i have done following things. Referred https://docs.zephyrproject.org/1.14.0/samples/subsys/mgmt/mcumgr/smp_svr/README.html?highlight=bui

#nrf52840 #ble #bluetoothmesh

Hi Adam, Thanks for the quick reply.I have flashed MCUBOOT (0x0 to 0x8000) and smp_svr (0xC000 to 0x27000). The flag CONFIG_UART_MCUMGR_ON_DEV_NAME is defaults to 'UART_0'. My DTS file has following c

#ble #bluetoothmesh #nrf52840 #uart

Hi, I have nrf52840 on my custom board (Based on IMX6, Running Yocto linux) which is connected over UART. I want to do an OTA of zephyr OS on that chip over serial/ble and for that i had already tried

#ble #bluetoothmesh #nrf52840 #uart