Can't init device hci0: Cannot assign requested address (99) #nrf52
|
akshaykulkarniak@...
Hi there ,
I am trying to bring up a BT (HCI interface) module connected to a qualcomm chipset
Trying to bring up the interface using hciconfig but it fails with error no.99 .
Note : ttyUSB here is a cp210x (USB-UART bridge) connected via HSIC
Below are the logs
root@swi-mdm9x28-wp:~# hciattach -s 115200 /dev/ttyUSB2 any 115200 noflow nosleep
Device setup complete
root@swi-mdm9x28-wp:~# hciconfig -a
hci0: Type: Primary Bus: UART
BD Address: 00:00:00:00:00:00 ACL MTU: 27:7 SCO MTU: 0:0
DOWN
RX bytes:205 acl:0 sco:0 events:14 errors:0
TX bytes:80 acl:0 sco:0 commands:14 errors:0
Features: 0x00 0x00 0x00 0x00 0x60 0x00 0x00 0x00
Packet type: DM1 DH1 HV1
Link policy:
Link mode: MASTER
root@swi-mdm9x28-wp:~# hciconfig hci0 up
Can’t init device hci0: Cannot assign requested address (99)
root@swi-mdm9x28-wp:~# hciconfig hci0 up
Can’t init device hci0: Cannot assign requested address (99)
root@swi-mdm9x28-wp:~# hciconfig hci0 up
Can’t init device hci0: Cannot assign requested address (99)
root@swi-mdm9x28-wp:~# hciconfig hci0 up
Can’t init device hci0: Cannot assign requested address (99)
root@swi-mdm9x28-wp:~# hciconfig hci0 up
Can’t init device hci0: Cannot assign requested address (99)
Below are the Details of the Chipset
Module : Sierra Wireless WP7608 (Chipset : QC MDM9x28)
Linux Kernel version : 3.18.140
Yocto Project : 2.5
Please Let me know a possible solution to overcome this .
Thanks & Regards
- Akshay
|
|
|
|
lairdjm
Hi Akshay, 00:00:00:00:00:00 is not a valid Bluetooth address, set a valid Bluetooth address and try again Thanks, Jamie
From: devel@... <devel@...>
On Behalf Of akshaykulkarniak via lists.zephyrproject.org
Sent: 23 June 2021 10:45 To: devel@... Subject: [Zephyr-devel] Can't init device hci0: Cannot assign requested address (99) #nrf52 #nrf52 #nrf52
Hi there , I am trying to bring up a BT (HCI interface) module connected to a qualcomm chipset Trying to bring up the interface using hciconfig but it fails with error no.99 .
Note : ttyUSB here is a cp210x (USB-UART bridge) connected via HSIC
Below are the logs
root@swi-mdm9x28-wp:~# hciattach -s 115200 /dev/ttyUSB2 any 115200 noflow nosleep Device setup complete
root@swi-mdm9x28-wp:~# hciconfig -a hci0: Type: Primary Bus: UART BD Address: 00:00:00:00:00:00 ACL MTU: 27:7 SCO MTU: 0:0 DOWN RX bytes:205 acl:0 sco:0 events:14 errors:0 TX bytes:80 acl:0 sco:0 commands:14 errors:0 Features: 0x00 0x00 0x00 0x00 0x60 0x00 0x00 0x00 Packet type: DM1 DH1 HV1 Link policy: Link mode: MASTER
root@swi-mdm9x28-wp:~# hciconfig hci0 up Can’t init device hci0: Cannot assign requested address (99) root@swi-mdm9x28-wp:~# hciconfig hci0 up Can’t init device hci0: Cannot assign requested address (99) root@swi-mdm9x28-wp:~# hciconfig hci0 up Can’t init device hci0: Cannot assign requested address (99) root@swi-mdm9x28-wp:~# hciconfig hci0 up Can’t init device hci0: Cannot assign requested address (99) root@swi-mdm9x28-wp:~# hciconfig hci0 up Can’t init device hci0: Cannot assign requested address (99)
Below are the Details of the Chipset
Module : Sierra Wireless WP7608 (Chipset : QC MDM9x28) Linux Kernel version : 3.18.140 Yocto Project : 2.5
Please Let me know a possible solution to overcome this .
Thanks & Regards - Akshay
|
|
|