Re: [Zephyr-devel] MPU fault while testing Bluetooth Mesh Sample demos


vikrant8051 <vikrant8051@...>
 

Hi Jiri,
After replying to your email, I once again started testing thoroughly.
And yes, once again I got MPU fault.

Regards,
Vikrant


On Mon, Sep 17, 2018 at 6:30 PM vikrant8051 <vikrant8051@...> wrote:
HI Jiri,
After latest sync with master, I've not faced MPU FAULT issue
while testing. But it could be there. With v1.13, it could be suddenly
pops-up without any reason (as a app developer)

Thanks for linking your issue with this mailing list. Hope Zephyr
core developers will resolve it.

Regards,
vikrant



On Mon, Sep 17, 2018 at 12:37 PM Jiří Kubias <jiri.kubias@...> wrote:
Hi,
have you found a solution? Few days ago I have reported similar problem with MPU fault but with Atmel (Microchip) SAME70 chip. It is cased by binding DMA. 

    dev_cfg->dev_dma = device_get_binding(CONFIG_SPI_SAM_DMA_NAME);
if (!dev_cfg->dev_dma) {
SYS_LOG_ERR("%s device not found", CONFIG_SPI_SAM_DMA_NAME);
return -ENODEV;
}


and the console output  is

***** MPU FAULT *****
 Data Access Violation
 MMFAR Address: 0x412198
***** Hardware exception *****
Current thread ID = 0x204024b4
Faulting instruction address = 0x40e376
Fatal fault in essential thread! Spinning...


So far I didnt solved the issue, but I didnt had a much time to debug it. 

Best regards, 
Jiri



2018-09-14 12:33 GMT+02:00 vikrant8051 <vikrant8051@...>:
Hi Carles,
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

>> Did you run addr2line in 0x20001c5c?


***** MPU FAULT *****                                                                                                            
  Instruction Access Violation                                                                                                   
***** Hardware exception *****                                                                                                   
Current thread ID = 0x20001884                                                                                                   
Faulting instruction address = 0x20001c88                                                                                        
Fatal fault in ISR! Spinning...


1)

/opt/zephyr-sdk/sysroots/x86_64-pokysdk-linux/usr/bin/arm-zephyr-eabi/arm-zephyr-eabi-addr2line -e  /home/vikrant/zephyr/samples/boards/nrf52/mesh/onoff_level_lighting_vnd_app/build/zephyr/zephyr.elf 0x20001c88


&


/opt/zephyr-sdk/sysroots/x86_64-pokysdk-linux/usr/bin/arm-zephyr-eabi/arm-zephyr-eabi-addr2line -e  /home/vikrant/zephyr/samples/boards/nrf52/mesh/onoff_level_lighting_vnd_app/build/zephyr/zephyr.elf 0x20001884


Both returns -> :? ...... with zephyr-SDK


2)

I also tried to compile the App using latest gcc-arm-none-eabi-7-2018-q2


2.1)

/opt/gcc-arm-none-eabi-7-2018-q2-update/bin/arm-none-eabi-addr2line -e /home/vikrant/zephyr/samples/boards/nrf52/mesh/onoff_level_lighting_vnd_app/build/zephyr/zephyr.elf 0x20001c88


o/p -> isr_tables.c:?


2.2)

/opt/gcc-arm-none-eabi-7-2018-q2-update/bin/arm-none-eabi-addr2line -e /home/vikrant/zephyr/samples/boards/nrf52/mesh/onoff_level_lighting_vnd_app/build/zephyr/zephyr.elf 0x20001884


o/p -> /home/vikrant/zephyr/kernel/init.c:80

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

>> Have you tried increasing stack sizes?


Yes.

CONFIG_MAIN_STACK_SIZE=512 ....to 1024
CONFIG_SYSTEM_WORKQUEUE_STACK_SIZE=2048 ....to 4096


But still getting MPU Fault in case of Board executing BT Mesh Servers.


On Fri, Sep 14, 2018 at 3:31 PM Cufi, Carles <Carles.Cufi@...> wrote:

Hi there,

 

Did you run addr2line in 0x20001c5c?

Have you tried increasing stack sizes?

 

Carles

 

From: devel@... <devel@...> On Behalf Of vikrant8051
Sent: 14 September 2018 11:48
To: devel@...; users@...
Subject: Re: [Zephyr-devel] MPU fault while testing Bluetooth Mesh Sample demos

 

Hi,

 

FYI,

With v1.12.99 I'm mot facing any MPU FAULT issue (while testing for #onoff_level_lighting_vnd_app)

It has last commit -> ba6763a187a347cfc825a2bece78e7d1ef28772d

 

That means something after it has changed the things bcz of that we are getting

MPU FAULT.

 

Thank You !!

 

On Wed, Sep 5, 2018 at 10:50 AM vikrant8051 <vikrant8051@...> wrote:

Hi,

I'm getting following MPU fault while testing with samples for Bluetooth Mesh . This issue has started after syncing with master branch.

 

***** MPU FAULT *****                                                                                                            
  Instruction Access Violation                                                                                                   
***** Hardware exception *****                                                                                                   
Current thread ID = 0x2000188c                                                                                                   
Faulting instruction address = 0x20001c5c                                                                                        
Fatal fault in ISR! Spinning...

 

 

Thank You !!

 

 




--
===================================================
Ing. Jiri Kubias
 
e-mail: jiri.kubias@...
mobile: 775 593 956
===================================================

Join users@lists.zephyrproject.org to automatically receive all group messages.