users@lists.zephyrproject.org

Re: [devel] Zephyr SDK 0.9 released

Hello, "Nashif, Anas" <anas.nashif@...> wrote: Based on md5sum, that's the same file as had been announced a week before. So, people who downloaded it may check their md5 and save

By Paul Sokolovsky · #1 ·

Writing to UART_B of D2000 with Zephyr

Dear community, I am developing for D2000 with Zephyr and I currently need to be able to write to the UART B and to monitor it. However, I cannot manage to do it. For writing to the UAR I am

By MIKHALEV, Vasily <vasily.mikhalev@...> · #2 ·

Re: Writing to UART_B of D2000 with Zephyr

Hi Vasily! How are you doing? some points that can help you: - Did you check the pointer received to you dev_b variable after a call of device binding? is it null? - Check the platform pin-mux to see

By Felipe Neves · #3 ·

Re: Writing to UART_B of D2000 with Zephyr

Hi Felipe, I am doing good. How are you? Thank you very much for your help! Did you check the pointer received to you dev_b variable after a call of device binding? is it null? I’ve

By MIKHALEV, Vasily <vasily.mikhalev@...> · #4 ·

Intel Pattern Matching in Zephyr?

Hi Just wondering if anybody used the PM technology with zephyr. There is code for the arduino IDE but I don't know how difficult would be to port it regards

By Carles Perello · #5 ·

Re: Intel Pattern Matching in Zephyr?

Hi, I have been trying to use it a bit. The open source code is here. https://github.com/01org/Intel-Pattern-Matching-Technology It is bit out of date but with a little bit tweaking you

By Poussa, Sakari · #6 ·

Re: Intel Pattern Matching in Zephyr?

Hey guys. If this library is available to Arduino 101 and TinyTile (as shown in github), and all code base for it is referenced on Intel QMSI library, I think the PME engine is already supportend on

By Felipe Neves · #7 ·

Issue when debugging STM32 board with zephyr openocd

Hi, I've faced an issue when trying to debug using zephyr openocd ("make BOARD=... debug"). Problem happens in step by step debug where I suddenly jump in an unrelated function. I don't face such

By Erwan Gouriou · #8 ·

Re: Issue when debugging STM32 board with zephyr openocd

Hi Erwan, Did you build the zephyr project with some optimization flags? such -Os? Also, in menu config during kernel configuration phase, have you enabled the debug symbol generation? Also, you need

By Felipe Neves · #9 ·

Re: Issue when debugging STM32 board with zephyr openocd

Hi Felipe, Thanks for this answer. I did not build with specific optimization flag, I did not enable symbol generation neither. Steps to reproduce are as follows: $make BOARD=nucleo_f4... debug >>b

By Erwan Gouriou · #10 ·

Re: Intel Pattern Matching in Zephyr?

Hello guys, I have some experience with the PME and have documented some of the examples. https://github.com/vraoresearch/Intel-Pattern-Matching-Technology While the Arduino library has all the

By Vinay R Rao <vinay.rao@...> · #11 ·

Re: Intel Pattern Matching in Zephyr?

Hi Vinay, thanks for the very useful information, I'll take a look on the supplied link :) A question to you, did you use the intel QMSI software package as interface between physical registers and

By Felipe Neves · #12 ·

Build of samples/hello_world for Arduino 101 fails with SDK v0.9 works with SDK v0.8.2

I was testing out building the v1.6.0 kernel using SDK v0.9 for BOARD=arduino_101 and it failed. I was able to build it using the SDK v0.8.2, but it failed to flash via openOCD. I´m using Ubuntu

By Alex Molina · #13 ·

Re: Build of samples/hello_world for Arduino 101 fails with SDK v0.9 works with SDK v0.8.2

Seems like something isn’t right with your zephyr-sdk-0.9 install. What do you get for: ls /home/alexm/swdev/zephyr-sdk-0.9/sysroots/i686-pokysdk-linux/usr/bin/iamcu-poky-elfiamcu - k

By Kumar Gala · #14 ·

Re: Build of samples/hello_world for Arduino 101 fails with SDK v0.9 works with SDK v0.8.2

Looks like you are still using the 0.8.2 SDK? Seems like something isn’t right with your zephyr-sdk-0.9 install. What do you get for: ls

By Nashif, Anas · #15 ·

Re: Build of samples/hello_world for Arduino 101 fails with SDK v0.9 works with SDK v0.8.2

It’s an openocd path issue. SDK0.9 is using x86_64, not i686. Please try to add the following lines to .zephyrrc if you are using it. export

By Qiu, PeiyangX <peiyangx.qiu@...> · #16 ·

Zephyr GDB python scripts?

Hi there! I'm new to Zephyr. I was looking for gdb python scripts that add commands/shortcuts to gdb to do helpful things like dump memory pool blocks, print out status of sync primitives, etc. Does

By The, Martijn <martijn.the@...> · #17 ·

How to write a string to serial?

Hi all I am new to this mailing list. I connect my arduino 101 to minicom, I have set the serial port: ttyUSB0 8N1 I use the Adafruit 4 pin cable (PL2303) black Ground connect GND on arduino

By kk <pinganddu90@...> · #18 ·

How to write a string to serial?

Hi all I am new to this mailing list. I connect my arduino 101 to minicom, I have set the serial port: ttyUSB0 8N1 I use the Adafruit 4 pin cable (PL2303) black Ground connect GND on arduino

By kk <pinganddu90@...> · #19 ·

Re: How to write a string to serial?

If you just use printf() you will get strings outputted to serial with most default configurations. - k

By Kumar Gala · #20 ·

Messages