Hello, "Nashif, Anas" <anas.nashif@...> wrote: Based on md5sum, that's the same file as had been announced a week before. So, people who downloaded it may check their md5 and save

Dear community, I am developing for D2000 with Zephyr and I currently need to be able to write to the UART B and to monitor it. However, I cannot manage to do it. For writing to the UAR I am

Hi Vasily! How are you doing? some points that can help you: - Did you check the pointer received to you dev_b variable after a call of device binding? is it null? - Check the platform pin-mux to see

Hi Felipe, I am doing good. How are you? Thank you very much for your help! Did you check the pointer received to you dev_b variable after a call of device binding? is it null? I’ve

Hi Just wondering if anybody used the PM technology with zephyr. There is code for the arduino IDE but I don't know how difficult would be to port it regards

Hi, I have been trying to use it a bit. The open source code is here. https://github.com/01org/Intel-Pattern-Matching-Technology It is bit out of date but with a little bit tweaking you

Hey guys. If this library is available to Arduino 101 and TinyTile (as shown in github), and all code base for it is referenced on Intel QMSI library, I think the PME engine is already supportend on

Hi, I've faced an issue when trying to debug using zephyr openocd ("make BOARD=... debug"). Problem happens in step by step debug where I suddenly jump in an unrelated function. I don't face such

Hi Erwan, Did you build the zephyr project with some optimization flags? such -Os? Also, in menu config during kernel configuration phase, have you enabled the debug symbol generation? Also, you need

Hi Felipe, Thanks for this answer. I did not build with specific optimization flag, I did not enable symbol generation neither. Steps to reproduce are as follows: $make BOARD=nucleo_f4... debug >>b

Hello guys, I have some experience with the PME and have documented some of the examples. https://github.com/vraoresearch/Intel-Pattern-Matching-Technology While the Arduino library has all the

Hi Vinay, thanks for the very useful information, I'll take a look on the supplied link :) A question to you, did you use the intel QMSI software package as interface between physical registers and

I was testing out building the v1.6.0 kernel using SDK v0.9 for BOARD=arduino_101 and it failed. I was able to build it using the SDK v0.8.2, but it failed to flash via openOCD. I´m using Ubuntu

Seems like something isn’t right with your zephyr-sdk-0.9 install. What do you get for: ls /home/alexm/swdev/zephyr-sdk-0.9/sysroots/i686-pokysdk-linux/usr/bin/iamcu-poky-elfiamcu - k

Looks like you are still using the 0.8.2 SDK? Seems like something isn’t right with your zephyr-sdk-0.9 install. What do you get for: ls

It’s an openocd path issue. SDK0.9 is using x86_64, not i686. Please try to add the following lines to .zephyrrc if you are using it. export

Hi there! I'm new to Zephyr. I was looking for gdb python scripts that add commands/shortcuts to gdb to do helpful things like dump memory pool blocks, print out status of sync primitives, etc. Does

Hi all I am new to this mailing list. I connect my arduino 101 to minicom, I have set the serial port: ttyUSB0 8N1 I use the Adafruit 4 pin cable (PL2303) black Ground connect GND on arduino

Hi all I am new to this mailing list. I connect my arduino 101 to minicom, I have set the serial port: ttyUSB0 8N1 I use the Adafruit 4 pin cable (PL2303) black Ground connect GND on arduino

If you just use printf() you will get strings outputted to serial with most default configurations. - k