Hi Justin, "Justin Huang via Lists.Zephyrproject.Org" <justin.y.huang=live.com@...> writes: DEVICE_GET() might not be the right thing here. Are you trying to get a pointer to

Hello, "yasokada via Lists.Zephyrproject.Org" <yasokada=gmail.com@...> writes: That is not correct. An "in-tree" build is when build artifacts (object files, generated code,

Hi, I am building a device driver for Zephyr and when calling the macro, DEVICE_GET(), likeDEVICE_GET(my_dev), I get a build error complaining about undefined__device_my_dev. I tried to locate where

Hi, I am building a device driver for Zephyr and when calling the macro, DEVICE_GET(), like DEVICE_GET(my_dev), I get a build error complaining about undefined __device_my_dev. I tried to locate where

Hi there In my application I try to use NVS on an external SPI flash (M25P16) which has an erase page size of 64k. As I realised, NVS seems to have some limit on its maximum sector size of just below

My environment: Ubuntu 18.04 LTS STM32L476 Nucleo_64 (hereafter STM32L476) STM32F769 Discovery Kit (hereafter STM32F769) Zephyr 2.1.0-rc1 Project: `samples/subsys/fs/fat_fs` Logic Analyzer: Analog

Dear Yannis (I have sent private reply, but for other people, I send this reply again). Thank you very much. I added the description for &spi2 in an overlay file. It worked. I appreciate it.

-------- Forwarded Message -------- Subject: Private: Re: [Zephyr-users] SPI2 definition is not found for STM32L476 device tree. How to add? Date: Fri, 27 Dec 2019 15:40:46 -0800 From:

Hi, You don't need to add it. It exists in dts/arm/st/l4/stm32l471.dtsi To enable it just add the following in nucleo_l476rg.dts or an overlay file: &spi2 { status = "okay"; }; Yannis

My environment: Ubuntu 18.04 LTS STM32L476 Nucleo_64 (hereafter STM32L476) STM32F769 Discovery Kit (hereafter STM32F769) Zephyr 2.1.0-rc1 ### SPI2 for STM32L476

Good day, I have decided to dive head first into Zephyr with a project of mine. I have a LIS2DH and a W25Q128JV Flash on the same SPI bus, with two GPIOs to control the chip selects. I have a

Please follow this, if using hci_uart: https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/nrf5x-support-within-the-zephyr-project-rtos Else if using hci_usb and the nRF52840’s

I have build and flashed the zephire/sample/bluetooth/hci_uart on nrf52840 board and connected the board with ubuntu but hci interface was not created when checked using hciconfig. Can you please

I am attempting to create a simple SPI-Slave implementation for the nRF52 PCA10040 board. My project’s source code is at https://github.com/foldedtoad/spi_slave. While I am able to receive

Hi all, This week we will focus on two Stable API Change RFCs and GPIO. I am unable to attend but Peter Bigot has kindly offered to chair the meeting instead. Reminder on the Stable API Change RFCs:

Hello Zephyr users, Now that Zephyr 2.1 has been released, I am proposing we make Python 3.6 the minimum supported Python version for

Hi Pauli, If you are able to do what you want with Cube HAL then, to interface with zephyr, you just need to redefine the HAL callback (defined as weak in HAL drivr) in your zephyr application. You

Dear all, I am doing silly motor driver for worm-gear dc-motor with stm32f411e-disco board (and L298). The dc-motor has HAL-sensor for feedback - providing raising/lowering edge for every turn. Now,

Hi all, This week we will focus on API Changes and GPIO: - Changing a stable API: - https://github.com/zephyrproject-rtos/zephyr/pull/21013 - GPIO: Update on progress - Look at the PRs with

Hi, Iam using nrf52840 DK as a BLE controller. So i compiled a hex file and loaded into it. There after when we power on am getting the bdaddr of the device as 00:00:00:00:00:00, But when i check