Hi, Almost a year ago logging subsystem v2 was merged as an optional engine. It has the same user API but backend API has changed (see https://docs.zephyrproject.org/latest/reference/logging/index.htm

Hi, I found that idle thread is executed before main thread and I am not sure if it is by design or it is by coincidence or maybe it is purely my setup problem. What I did is adding 2 lines to idle th

Hello, i've two 52840DK,Windows10 X64, D:\Program\ncs_v1.8.0\zephyr\samples\bluetooth\periodic_adv D:\Program\ncs_v1.8.0\zephyr\samples\bluetooth\periodic_sync IDE is in dir D:\Program\v1.8.0\toolchai

I've been trying to get Zephyr installed in my Ubuntu VM by following https://docs.zephyrproject.org/2.7.0/getting_started/index.html , but when it comes to testing the hello_world sample the terminal

I just installed Zephyr with all the features and toolchain and stuff, by following https://docs.zephyrproject.org/2.7.0/getting_started/index.html . The thing is, right after that, I'm now trying to

Hi, It seems as though there are two ways to invoke a callback when a BLE device has been scanned. I can register a callback with bt_le_scan_cb_register, where my callback is the .recv field of the bt

Hi, I have a question concerning the LwM2M composite observe feature: is it already supported? If so, since which release? If not, are there any plans when it will be supported? I've already looked th

Hello, I am using an STM32H743ZI and have been trying to get PWM output on timers3. I have been able to successfully obtain output for all of the pins/channels I require on timers2, and tim3_ch1_pc6 o

Hi All, I'm trying to flash code, and boot out of the QSPI memory on the MIMXRT1050 EVKB board. Does anyone have experience with this? I've been unable to successfully flash so far. Here are the steps

New here just stumbled on Zephyr. I come from a PIC background and moved to STM32, loved it.... except the HAL framework... I like how everything is integrated in Zephyr and how easy it is to put to g

Hi Gerson Thank you for replying me. My board is PSoC6 WiFi-BT Pioneer Kit, Exactly the same as the boards on the Zephyr website. The link I refer to is https://docs.zephyrproject.org/latest/boards/ar

Hi Jason, Are you using P13-0, P13-1 ? See below: The PSoC-6 has a weird connection with an onboard psoc programmer. It uses the same pins from the Arduino UART Connector. To enable shields, uart was

Hi all I have downloaded the zephyr project completely, I plan to use the cy8ckit_062_wifi_bt_m0 board, I have built successfully, there is no error, but there is no log output in the corresponding de

Hi, is there an option to run SPI on zephyr driver with MOSI with option Active_Low? I would really appreciate your answer. Best regards, Dominika Sułot

Howdy y'all, I am working on bringing up some of the features on the Laird BT610 board. I've been able to bring up the digital and magnetic sensors. However, I'm a bit confused with the analog and tem

Hi, I’m developing a broadcast audio application with the nRF5340 SoC, based on the iso_broadcast and iso_receive sample. At the moment, I can connect the broadcaster with multiple receivers and trans

Hi Zephyr users! I'm new to Zephyr and was asked to write a small "study" project in c++. I didn't find much in the documentation about c++, except one sample and the following page: https://docs.zeph

In our project we are using the microcontroller STM32H753. We are trying to use mcuboot with the sample smp_svr (overlay-udp.conf) for software updates over Ethernet. This has been working good for th

I am trying to get my code to build with C++ exceptions enabled. Here are my configurations: CONFIG_CPLUSPLUS=y CONFIG_NEWLIB_LIBC=y CONFIG_LIB_CPLUSPLUS=y CONFIG_MINIMAL_LIBC=n CONFIG_NEWLIB_LIBC_NAN

Hi All, We're trying to turn on debug optimizations, with C++ support. We have the following settings in our prj.conf: CONFIG_DEBUG_OPTIMIZATIONS=y CONFIG_NO_OPTIMIZATIONS=y but this leads to an undef